Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0435240 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  C050623  Right Front Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C050612

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>C050612

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C050623 Right Front Wheel Speed Sensor Signal Stuck Low
·

When the vehicle is driven from 0 km/h to 12 km/h (0 mph to 7 mph), the wheel speed is 1.8 km/h (1.1 mph) or less for 0.6 seconds or more.

·

When the wheel speed has not exceeded 1.8 km/h (1.1 mph), the vehicle speed reaches 18 km/h (11 mph).

·

When the vehicle speed and wheel speed are both 50.4 km/h (31.3 mph) or more, the pulse signal is not detected for 0.08 seconds or more.


·

Front speed sensor RH

·

Speed sensor installation


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>TEST MODE PROCEDURE

·

DTC precaution

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>PRECAUTION

Procedure to clear warning lights (When not clearing DTCs)
Procedure
1.

Repair or replacement.

2.

Turn the ignition switch to ON.

3.

Drive the vehicle at 2 km/h (1 mph) or more to clear the warning lights.





PROCEDURE

1.CHECK FREEZE FRAME DATA (WHEEL SPEED)
a.

Select a DTC to display the Freeze Frame Data.


b.

Read the freeze frame data of DTC C050623.

Chassis > Brake
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > DTC(C050623) > Freeze Frame Data
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50040 435 13,14,15,16 C050623

Result:
Result Proceed to
The value of FR Wheel Speed is 2 km/h (1 mph) or less when all other values are 12 km/h (7 mph) or more. A
The value of FR Wheel Speed is 2 km/h (1 mph) or less when all other values are 50 km/h (31 mph) or more. B



A

2.READ VALUE USING GTS (FR WHEEL SPEED)

B

3.CHECK FRONT SPEED SENSOR RH INSTALLATION
2.READ VALUE USING GTS (FR WHEEL SPEED)
a.

Check the Data List using the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
FR Wheel Speed
50003 435 13

b.

Turn the ignition switch to ON (READY) and perform a road test.


c.

Check that the value of FR Wheel Speed changes in accordance with vehicle speed when accelerating from 0 km/h to 20 km/h (0 mph to 12 mph).

OK:

The value of FR Wheel Speed changes in accordance with vehicle speed.


HINT:

If the result of the road test is within the specified range, it is possible that this DTC was stored due to a particular situation such as brake drag, wheelspin or wheel lockup.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK FRONT SPEED SENSOR RH INSTALLATION
3.CHECK FRONT SPEED SENSOR RH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor RH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Check the front speed sensor RH installation.

OK:

There is no clearance between the front speed sensor RH and the steering knuckle RH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR RH