Home › Power Source / Network › NETWORKING › CXPI COMMUNICATION SYSTEM › from 2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0420499 CXPI COMMUNICATION SYSTEM C

NETWORKING  CXPI COMMUNICATION SYSTEM  B235387  Power Integration No.2 System Missing Message  


DESCRIPTION

This DTC is stored when CXPI communication between the No. 2 semiconductor power integration ECU, power distribution box assembly, windshield wiper relay assembly or light control LED ECU and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B235387 Power Integration No.2 System Missing Message No communication between No. 2 semiconductor power integration ECU and main body ECU (multiplex network body ECU) for 10 seconds or more
·

No. 2 semiconductor power integration ECU

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

C433513E02
0.656,0.49 2.26,0.74 1.604,0.25 10 false from Auxiliary Battery 1.031,1.323 2.26,1.521 1.229,0.198 10 false from IGP Relay 2.667,0.677 3.896,0.875 1.229,0.198 10 false PTC HTR 2.542,1.51 3.771,1.708 1.229,0.198 10 false ECU-IGP NO.3 3.656,0.521 3.979,0.677 0.323,0.156 10 false A87 4.042,0.531 4.365,0.688 0.323,0.156 10 false +B 3.729,0.323 4.052,0.479 0.323,0.156 10 false 1 3.646,1.365 3.969,1.521 0.323,0.156 10 false A88 4.042,1.375 4.365,1.531 0.323,0.156 10 false IG 3.719,1.146 4.042,1.302 0.323,0.156 10 false 9 3.646,2.417 3.969,2.573 0.323,0.156 10 false A88 3.719,2.198 4.042,2.354 0.323,0.156 10 false 7 4.021,2.417 4.427,2.604 0.406,0.188 10 false CXPI 4.01,4.104 4.417,4.292 0.406,0.188 10 false GND1 3.646,4.104 3.969,4.26 0.323,0.156 10 false A88 3.677,3.896 3.917,4.052 0.24,0.156 10 false 13 6.115,1.865 7.083,2.083 0.969,0.219 10 false to Each Load 2.542,2.25 2.865,2.406 0.323,0.156 10 false 13 2.104,2.427 2.51,2.615 0.406,0.188 10 false CXP2 1.188,2.969 1.51,3.125 0.323,0.156 10 false H4 1.167,3.125 2.833,3.5 1.667,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 3.969,4.771 5.76,5.156 1.792,0.385 10 false No. 2 Semiconductor Power Integration ECU 0.823,5.49 3.25,5.667 2.427,0.177 10 false : CXPI Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Result
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B235387 is output A
DTC B235387 is not output B



A

3.CHECK HARNESS AND CONNECTOR (NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU - BATTERY AND BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the A87 and A88 No. 2 semiconductor power integration ECU connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A88-13 (GND1) - Body ground Always Below 1 Ω



e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A87-1 (+B) - Body ground Ignition switch off 8 to 14 V
A88-9 (IG) - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the A88 No. 2 semiconductor power integration ECU connector.


d.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A88-7 (CXPI) - H4-13 (CXP2) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A88-7 (CXPI) - Body ground Cable disconnected from negative (-) auxiliary battery terminal 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU
a.

Replace the No. 2 semiconductor power integration ECU with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


Result:
Result
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Result
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B235387 is output A
DTC B235387 is not output B



A

END (NO. 2 SEMICONDUCTOR POWER INTEGRATION ECU WAS DEFECTIVE)

B