Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _088062 SEAT BELT _0421675 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



Hide 73350C 3.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)

Hide 4.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)

Hide 72693 5.REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)

Hide 76974F 6.REMOVE REAR UNDER SIDE COVER (for HV Model)

Hide 67917F 7.REMOVE REAR DOOR SCUFF PLATE INSIDE

Hide 62331A 8.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the rear door opening trim weatherstrip.


Hide 67913B 9.REMOVE FRONT DOOR SCUFF PLATE

Hide 62311B 10.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the front door opening trim weatherstrip.


Hide 73233 11.REMOVE LAP BELT OUTER ANCHOR COVER

a.
B583419C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws and guide to remove the lap belt outer anchor cover as shown in the illustration.


Hide 73210 12.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.
B583420

Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.


Hide 62413A 13.REMOVE CENTER PILLAR LOWER GARNISH

Hide 62411B 14.REMOVE CENTER PILLAR UPPER GARNISH

Hide 73210 15.REMOVE FRONT SEAT OUTER BELT ASSEMBLY

a.
B583421

Remove the bolt to disconnect the shoulder anchor of the front seat outer belt assembly.


b.

Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.

B583521C01
1.208,0.698 1.5,0.896 true 4.531,0.698 4.823,0.896 true 1.125,0.302 1.313,0.469 true 4.458,0.292 4.646,0.458 true 0.042,0.052 0.375,0.281 0.333,0.229 12 false *A 3.74,0.063 4.031,0.281 0.292,0.219 12 false *B 1.531,0.802 1.75,0.99 0.219,0.188 10 true *a 0.938,0.167 1.25,0.323 0.313,0.156 10 false *b 4.844,0.802 5.063,0.99 0.219,0.188 10 true *a 4.271,0.167 4.583,0.323 0.313,0.156 10 false *b
*A for TMMF Made *B for TMC Made
*a Protective Tape *b Locking Button



c.
B583423

Remove the 2 bolts.


d.

Disengage the guides to remove the front seat outer belt assembly.