Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _088062 SEAT BELT _0421678 REAR SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear seat outer belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

·

After disconnecting the cable from the negative (-) auxiliary battery terminal, wait for at least 90 seconds to start the operation.


·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 64330D 3.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

Hide 58410B 4.REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)

Hide 64771G 5.REMOVE SPARE WHEEL COVER

Hide 64716D 6.REMOVE DECK TRIM REAR COVER

Hide 7.REMOVE REAR SEAT ASSEMBLY

Hide 76973F 8.REMOVE REAR UNDER SIDE COVER (for HV Model)

Hide 67917F 9.REMOVE REAR DOOR SCUFF PLATE INSIDE

Hide 62331A 10.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 71303C 11.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY

Hide 81330 12.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)

Hide 64714C 13.REMOVE DECK TRIM SIDE COVER

Hide 64730B 14.REMOVE DECK TRIM SIDE PANEL ASSEMBLY

Hide 73360D 15.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY

a.
B583431

Remove the bolt to disconnect the floor anchor of the rear seat outer belt assembly.


Hide 62471A 16.REMOVE ROOF SIDE INNER GARNISH

Hide 73360D 17.REMOVE REAR SEAT OUTER BELT ASSEMBLY

a.

Using a screwdriver with its tip wrapped in protective tape, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.

B583525C01
1.25,1.969 1.417,1.875 true 4.583,1.969 4.781,1.875 true 1.177,2.396 1.385,2.25 true 4.458,2.354 4.667,2.208 true 0.031,0.042 0.323,0.292 0.292,0.25 12 false *A 3.458,0.042 3.771,0.323 0.313,0.281 12 false *B 0.948,2.292 1.146,2.49 0.198,0.198 10 true *a 1.469,1.76 1.781,1.917 0.313,0.156 10 false *b 4.813,1.74 5.094,1.958 0.281,0.219 10 false *b 4.24,2.26 4.438,2.458 0.198,0.198 10 true *a
*A for TMMF Made *B for TMC Made
*a Protective Tape *b Locking Button



b.
B583433N01
1.292,0.188 1.552,0.458 0.26,0.271 10 true (A) 1.313,0.615 1.542,0.885 0.229,0.271 10 true (B) 0.854,1.906 1.094,2.156 0.24,0.25 10 true (C)

Remove the bolt (A) to disconnect the shoulder anchor of the rear seat outer belt assembly.


c.

Remove the bolt (B) and then bolt (C).


d.

Disengage the guides to remove the rear seat outer belt assembly.