Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0421871 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the horn button assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 45130 3.REMOVE HORN BUTTON ASSEMBLY

CAUTION:
B528833C01
0,0 0,0 false
V100155

Deployment Side


·

When storing the horn button assembly, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

for TMC Made:

i.

Using a screwdriver with its tip wrapped in protective tape, push in the torsion springs to disengage the pins as shown in the illustration.

NOTICE:

Do not drop the horn button assembly.


B594008C01
1.51,1.333 1.01,0.979 true 4.76,1.01 4.438,0.792 true 0.688,4.49 1.146,4.063 true 1.135,2.75 1.615,2.313 true 6.031,2.74 6.417,2.323 true 5.771,4.74 6.125,4.333 true 0.823,1.292 1.229,1.552 true 0.458,0.927 0.917,0.771 true 0.5,4.75 0.885,5.396 true 1.094,4.615 1.531,5.344 true 4.052,1.531 4.542,1.292 true 4.344,1.042 3.906,1.198 true 0.26,0.167 0.51,0.396 0.25,0.229 10 true *a 2.094,0.156 2.344,0.385 0.25,0.229 10 true *b 3.781,0.156 4.031,0.385 0.25,0.229 10 true *a 5.677,0.135 5.927,0.365 0.25,0.229 10 true *b 1.563,1.25 1.813,1.479 0.25,0.229 10 true *c 6.385,2.229 6.635,2.458 0.25,0.229 10 true *c 6.146,4.188 6.396,4.417 0.25,0.229 10 true *c 0.302,1.938 0.552,2.167 0.25,0.229 10 true *f 2.573,3.344 2.823,3.573 0.25,0.229 10 true *f 3.073,3.583 3.323,3.813 0.25,0.229 10 true *h 4.313,3.344 4.563,3.573 0.25,0.229 10 true *g 5.198,1.948 5.438,2.177 0.24,0.229 10 true *g 4.906,3.969 5.156,4.198 0.25,0.229 10 true *h 2.5,4.021 2.75,4.25 0.25,0.229 10 true *b 0.271,4.021 0.521,4.25 0.25,0.229 10 true *a 0.938,5.323 1.188,5.552 0.25,0.229 10 true *e 1.125,3.958 1.375,4.188 0.25,0.229 10 true *c 1.292,1.479 1.542,1.708 0.25,0.229 10 true *e 3.854,1.448 4.104,1.677 0.25,0.229 10 true *e 4.792,0.927 5.042,1.156 0.25,0.229 10 true *d 0.26,0.854 0.51,1.083 0.25,0.229 10 true *d 1.635,2.177 1.885,2.406 0.25,0.229 10 true *c 1.583,5.25 1.833,5.479 0.25,0.229 10 true *d 3.698,1.135 3.948,1.365 0.25,0.229 10 true *c
*a Lock Position *b Unlock Position
*c Torsion Spring *d Pin
*e Protective Tape *f View A
*g View B *h View C


HINT:

Insert the screwdriver into the installation areas of the lower No. 2 steering wheel cover and lower No. 3 steering wheel cover.




d.

for TMMF Made:

i.

Using a screwdriver with its tip wrapped in protective tape, push in the torsion springs to disengage the pins as shown in the illustration.

NOTICE:

Do not drop the horn button assembly.


B593499C01
1.51,1.333 0.969,0.948 true 4.76,1.01 4.281,0.76 true 0.854,4.573 1.146,4.063 true 1.094,2.677 1.615,2.313 true 6.115,2.667 6.417,2.323 true 6.01,4.729 6.229,4.354 true 0.771,1.25 1.229,1.552 true 0.458,0.927 0.917,0.771 true 0.604,4.813 0.885,5.313 true 1.26,4.708 1.531,5.344 true 4.052,1.531 4.448,1.26 true 4.24,1.042 3.906,1.198 true 0.25,0.167 0.5,0.396 0.25,0.229 10 true *a 2.167,0.188 2.417,0.417 0.25,0.229 10 true *b 3.75,0.167 4,0.396 0.25,0.229 10 true *a 5.583,0.188 5.833,0.417 0.25,0.229 10 true *b 1.563,1.25 1.813,1.479 0.25,0.229 10 true *c 6.385,2.229 6.635,2.458 0.25,0.229 10 true *c 6.198,4.188 6.448,4.385 0.25,0.198 10 true *c 0.25,1.833 0.5,2.063 0.25,0.229 10 true *f 2.792,3.271 3.042,3.5 0.25,0.229 10 true *f 3.198,3.573 3.448,3.802 0.25,0.229 10 true *h 4.417,3.344 4.667,3.573 0.25,0.229 10 true *g 5.083,1.833 5.323,2.063 0.24,0.229 10 true *g 5.083,4 5.333,4.229 0.25,0.229 10 true *h 2.75,4 3,4.229 0.25,0.229 10 true *b 0.167,4 0.417,4.229 0.25,0.229 10 true *a 0.875,5.365 1.125,5.594 0.25,0.229 10 true *e 1.125,3.958 1.375,4.188 0.25,0.229 10 true *c 1.292,1.479 1.542,1.708 0.25,0.229 10 true *e 3.854,1.448 4.104,1.677 0.25,0.229 10 true *e 4.792,0.927 5.042,1.156 0.25,0.229 10 true *d 0.26,0.854 0.51,1.083 0.25,0.229 10 true *d 1.635,2.177 1.885,2.406 0.25,0.229 10 true *c 1.458,5.365 1.708,5.594 0.25,0.229 10 true *d 3.698,1.135 3.948,1.365 0.25,0.229 10 true *c
*a Lock Position *b Unlock Position
*c Torsion Spring *d Pin
*e Protective Tape *f View A
*g View B *h View C


HINT:

Insert the screwdriver into the installation areas of the lower No. 2 steering wheel cover and lower No. 3 steering wheel cover.




e.
B583367C01
2.552,2.135 2.792,2.333 0.24,0.198 10 true *a 1.333,1.938 1.573,2.135 0.24,0.198 10 true *b
*a Horn Connector
*b Airbag Connector


Tilt the horn button assembly toward the seat and support it with one hand.

NOTICE:
·

Do not drop the horn button assembly.

·

When disconnecting the horn button assembly, do not pull the airbag wire harness.




f.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



g.

Disengage the wire harness clamp and disconnect the horn connector.