Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2020.07
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0421982 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the spiral cable with sensor sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Steering sensor (Including removal and installation) Adjust steering angle setting Parking assist monitor system (Click here)

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 45130 1.REMOVE HORN BUTTON ASSEMBLY

Hide 45100 2.REMOVE STEERING WHEEL ASSEMBLY

Hide 84306 3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

a.

Check that the front wheels are facing straight ahead.


b.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B593500C01
4.458,1.948 3.646,1.271 3.646,1.271 2.74,1.99 true 4.448,2.052 3.542,2.573 3.542,2.573 2.708,2.063 true 0.188,0.083 0.5,0.333 0.313,0.25 12 false *A 3.833,0.083 4.167,0.333 0.333,0.25 12 false *B 3.49,2.573 3.667,2.76 0.177,0.188 10 false *b 3.594,1.073 3.906,1.229 0.313,0.156 10 false *a
*A w/ Heated Steering Wheel System *B w/o Heated Steering Wheel System
*a Check Window *b Top of Flat Cable U-turn


NOTICE:

If the result is not as specified, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 45287 4.REMOVE LOWER STEERING COLUMN COVER

Hide 45286B 5.REMOVE UPPER STEERING COLUMN COVER

Hide 84306 6.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG).

·

When rotating the spiral cable with sensor sub-assembly to check the operation of the spiral cable with sensor sub-assembly (checking for abnormal noise, checking the Data List, etc.), make sure to perform the inspection with the steering wheel assembly installed.



a.

Disconnect each connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



b.
B593501

Disengage the claw and clips to remove the spiral cable with sensor sub-assembly.


Hide 89245B 7.REMOVE STEERING SENSOR

NOTICE:
·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.

·

Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in a misaligned center position of the steering sensor. Therefore, make sure to use the lock pin provided with a new spiral cable when removing the steering sensor from the spiral cable sub-assembly.



a.
B530115

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable.

·

Do not remove the lock pin before the spiral cable is installed to the steering sensor.




b.
B499966C07
2.156,0.385 2.469,0.833 true 0.708,1.25 1.083,1.5 true 2.76,1.167 2.5,1.417 true 1.979,0.271 2.292,0.427 0.313,0.156 10 false *a 1.083,1.417 1.281,1.594 0.198,0.177 10 true *b 2.302,1.333 2.5,1.51 0.198,0.177 10 true *b
*a Lock Pin
*b Guide


Disengage the claws and guides to remove the steering sensor from the spiral cable sub-assembly.