84306
1.INSPECT SPIRAL CABLE SUB-ASSEMBLY
Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.
Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.
Visually check the spiral cable sub-assembly for defects.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *A | w/o Steering Wheel Vibration | - | - |
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
- | - |
|
Interlock | - | - |
| *A | w/ Steering Wheel Vibration | *B | w/ ASL |
| *C | w/ Heated Steering Wheel System | - | - |
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
- | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Set the spiral cable sub-assembly to the center position.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H60-2(ECC) - z2-12(ECC) | Always | 3 Ω or less |
| H60-4(EAU) - z2-10(EAU) | Always | 3 Ω or less |
| H60-5(AU2) - z2-9(AU2) | Always | 3 Ω or less |
| H60-6(DIST) - z2-8(DIST) | Always | 3 Ω or less |
| H60-7(HO) - A(HO) | Always | 3 Ω or less |
| H60-9(ILL-) - z2-6(ILL-) | Always | 3 Ω or less |
| H60-10(+DP2) - z2-5(+DP2) | Always | 3 Ω or less |
| H60-11(+DP) - z2-4(+DP) | Always | 3 Ω or less |
| H60-12(AU1) - z2-3(AU1) | Always | 3 Ω or less |
| H60-13(CCS) - z2-2(CCS) | Always | 3 Ω or less |
| H60-14(IL+2) - z2-1(IL+2) | Always | 3 Ω or less |
| H38-1(D+) - z3-2(D+) | Always | Below 1 Ω |
| H38-2(D-) - z3-1(D-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H60-1(SDN) - z17-4(SDN) | Always | 3 Ω or less |
| H60-2(ECC) - z2-12(ECC) | Always | 3 Ω or less |
| H60-2(ECC) - z17-3(ECC) | Always | 3 Ω or less |
| H60-4(EAU) - z2-10(EAU) | Always | 3 Ω or less |
| H60-5(AU2) - z2-9(AU2) | Always | 3 Ω or less |
| H60-6(DIST) - z2-8(DIST) | Always | 3 Ω or less |
| H60-7(HO) - A(HO) | Always | 3 Ω or less |
| H60-8(SUP) - z17-2(SUP) | Always | 3 Ω or less |
| H60-9(ILL-) - z2-6(ILL-) | Always | 3 Ω or less |
| H60-10(+DP2) - z2-5(+DP2) | Always | 3 Ω or less |
| H60-11(+DP) - z2-4(+DP) | Always | 3 Ω or less |
| H60-12(AU1) - z2-3(AU1) | Always | 3 Ω or less |
| H60-13(CCS) - z2-2(CCS) | Always | 3 Ω or less |
| H60-14(IL+2) - z2-1(IL+2) | Always | 3 Ω or less |
| H72-3(LDA) - z16-3(LDA) | Always | 3 Ω or less |
| H72-1(LIN) - z16-2(LIN) | Always | 3 Ω or less |
| H38-1(D+) - z3-2(D+) | Always | Below 1 Ω |
| H38-2(D-) - z3-1(D-) | Always | Below 1 Ω |
| H72-2(EHT) - Z16-1(EHT) *1 | Always | Below 1 Ω |
| H72-4(BHT) - Z16-4(BHT) *1 | Always | Below 1 Ω |
| Z2-11(ASL) - H60-3(ASL) *2 | Always | 3 Ω or less |
*1: w/ Heated Steering Wheel System
*2: w/ ASL
If the result is not as specified, replace the spiral cable sub-assembly.