Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2020.07
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0421982 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

a.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B593502C01
2.5,1.583 3.26,0.531 3.26,0.531 4.729,0.979 true 2.479,1.635 3.427,1.833 3.427,1.833 4.74,1.042 true 4.521,1.708 4.594,2.438 4.594,2.438 4.635,1.635 true 1.24,1.729 1.313,2.458 1.313,2.458 1.354,1.656 true 0.167,0.167 0.479,0.323 0.313,0.156 12 false *A 3.417,0.167 3.74,0.354 0.323,0.188 12 false *B 3.167,0.323 3.479,0.479 0.313,0.156 10 false *a 1.24,2.469 1.448,2.625 0.208,0.156 10 true *c 4.458,0.583 4.771,0.74 0.313,0.156 10 false *d 3.354,1.854 3.531,2.031 0.177,0.177 10 true *b 4.552,2.479 4.76,2.635 0.208,0.156 10 true *c
*A w/ Heated Steering Wheel System *B w/o Heated Steering Wheel System
*a Check Window *b Top of Flat Cable U-turn
*c Matchmark - -



b.

If the spiral cable with sensor sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable with sensor sub-assembly.

·

When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B593503C01
1.719,1.938 1.719,1.344 true 1.635,1.969 1.948,2.125 0.313,0.156 10 false *a
*a Interlock
V113147

Counterclockwise


While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable with sensor sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


HINT:

The interlock operates at the top and bottom of the connector.



ii.
B593504

If the spiral cable with sensor sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B593505C01
1.969,1.177 2.813,1.177 true 2.854,1.094 3.167,1.25 0.313,0.156 10 false *a
*a Interlock
V113147

Clockwise


While pushing on the interlock, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



iv.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B593502C01
2.5,1.583 3.26,0.531 3.26,0.531 4.729,0.979 true 2.479,1.635 3.427,1.833 3.427,1.833 4.74,1.042 true 4.521,1.708 4.594,2.438 4.594,2.438 4.635,1.635 true 1.24,1.729 1.313,2.458 1.313,2.458 1.354,1.656 true 0.167,0.167 0.479,0.323 0.313,0.156 12 false *A 3.417,0.167 3.74,0.354 0.323,0.188 12 false *B 3.167,0.323 3.479,0.479 0.313,0.156 10 false *a 1.24,2.469 1.448,2.625 0.208,0.156 10 true *c 4.458,0.583 4.771,0.74 0.313,0.156 10 false *d 3.354,1.854 3.531,2.031 0.177,0.177 10 true *b 4.552,2.479 4.76,2.635 0.208,0.156 10 true *c
*A w/ Heated Steering Wheel System *B w/o Heated Steering Wheel System
*a Check Window *b Top of Flat Cable U-turn
*c Matchmark - -


NOTICE:

If the spiral cable with sensor sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 89245B 2.INSTALL STEERING SENSOR

a.
B499966C06
2.156,0.385 2.469,0.833 true 0.708,1.25 1.083,1.5 true 2.76,1.167 2.5,1.417 true 1.979,0.271 2.292,0.427 0.313,0.156 10 false *a 1.083,1.417 1.281,1.594 0.198,0.177 10 true *b 2.302,1.333 2.5,1.51 0.198,0.177 10 true *b
*a Lock Pin
*b Guide


Align the guides and engage the claws to install the steering sensor to the spiral cable sub-assembly.

NOTICE:
·

Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.

·

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.

·

The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.




b.

Remove the lock pin from the steering sensor.


Hide 3.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84306 4.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch on (IG).

·

When rotating the spiral cable with sensor sub-assembly to check the operation of the spiral cable with sensor sub-assembly (checking for abnormal noise, checking the DTC, Data list, etc.) make sure to perform the inspection with the steering wheel assembly installed.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

Check that the front wheels are facing straight ahead.


d.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch cancel ratchet may snap.



e.
B593501

Engage the claw and clips to install the spiral cable with sensor sub-assembly.


f.

Connect each connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



Hide 45286B 5.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 6.INSTALL LOWER STEERING COLUMN COVER

Hide 84306 7.ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B593500C01
4.458,1.948 3.646,1.271 3.646,1.271 2.74,1.99 true 4.448,2.052 3.542,2.573 3.542,2.573 2.708,2.063 true 0.188,0.083 0.5,0.333 0.313,0.25 12 false *A 3.833,0.083 4.167,0.333 0.333,0.25 12 false *B 3.49,2.573 3.667,2.76 0.177,0.188 10 false *b 3.594,1.073 3.906,1.229 0.313,0.156 10 false *a
*A w/ Heated Steering Wheel System *B w/o Heated Steering Wheel System
*a Check Window *b Top of Flat Cable U-turn



d.

If the spiral cable with sensor sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable with sensor sub-assembly.

·

When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B593506C01
0.552,0.958 1.604,0.958 true 0.365,0.865 0.677,1.021 0.313,0.156 10 false *a
*a Interlock
V113147

Counterclockwise


While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



ii.
B593507

If the spiral cable with sensor sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B593508C01
2.729,1.75 1.844,1.021 true 2.781,1.708 3.094,1.865 0.313,0.156 10 false *a
*a Interlock
V113147

Clockwise


While pushing on the interlock, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



iv.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B593500C01
4.458,1.948 3.646,1.271 3.646,1.271 2.74,1.99 true 4.448,2.052 3.542,2.573 3.542,2.573 2.708,2.063 true 0.188,0.083 0.5,0.333 0.313,0.25 12 false *A 3.833,0.083 4.167,0.333 0.333,0.25 12 false *B 3.49,2.573 3.667,2.76 0.177,0.188 10 false *b 3.594,1.073 3.906,1.229 0.313,0.156 10 false *a
*A w/ Heated Steering Wheel System *B w/o Heated Steering Wheel System
*a Check Window *b Top of Flat Cable U-turn


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 45100 8.INSTALL STEERING WHEEL ASSEMBLY

Hide 45130 9.INSTALL HORN BUTTON ASSEMBLY

Hide 12.PERFORM SYSTEM CALIBRATION (When Removing or Replacing the steering sensor)