If there is a malfunction in the power source circuit, the electric brake booster (brake booster with master cylinder assembly) stores a DTC, and ABS, brake assist, regenerative braking, etc. operation is prohibited by fail-safe control.
When a malfunction in the auxiliary battery, charging circuit, etc. results in a voltage differential between the +BS terminal and the internal circuit terminal of the electric brake booster (brake booster with master cylinder assembly), this DTC is stored.
When the voltage between the +BS terminal and the internal circuit terminal of the electric brake booster (brake booster with master cylinder assembly) returns to normal, this DTC is cleared.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C121F04 | Electronic Brake Booster Control Module "A" System Internal Failure | A voltage difference of 1.0 V or more is detected between the +BS terminal and the IGR terminal, and the voltage of the IGR terminal is 3.2 V or less. | Electric brake booster (brake booster with master cylinder assembly) | Brake Booster |
After replacing the electric brake booster (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".
Inspect the fuses for circuits related to this system before performing the following procedure.
Choose the model to be inspected
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A34 electric brake booster (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-1 (+BS) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A34 electric brake booster (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A34-20 (IGR) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A35 electric brake booster (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-1 (+BS) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A35 electric brake booster (brake booster with master cylinder assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A35-20 (IGR) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG