The relative displacement sensor sends the brake pedal stroke distance to the electric brake booster (brake booster with master cylinder assembly).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C127A11 | Electronic Brake Booster Input Stroke Sensor "A" Circuit Short to Ground | Open in relative displacement sensor (brake booster with master cylinder assembly) signal circuit for 0.1 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C127A15 | Electronic Brake Booster Input Stroke Sensor "A" Circuit Short to Battery or Open | Short in relative displacement sensor (brake booster with master cylinder assembly) signal circuit for 0.1 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C127A16 | Electronic Brake Booster Input Stroke Sensor "A" Circuit Voltage Below Threshold | Relative displacement sensor (brake booster with master cylinder assembly) output value is -3.9 mm or less for 0.2 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C127A17 | Electronic Brake Booster Input Stroke Sensor "A" Circuit Voltage Above Threshold | Relative displacement sensor (brake booster with master cylinder assembly) output value is 3.4 mm or more for 0.2 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C127A23 | Electronic Brake Booster Input Stroke Sensor "A" Signal Stuck Low | Relative displacement sensor (brake booster with master cylinder assembly) output value is less than 0.6 mm for 0.3 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C127A24 | Electronic Brake Booster Input Stroke Sensor "A" Signal Stuck High | Any of the following conditions are met:
·
Relative displacement sensor (brake booster with master cylinder assembly) output value abnormality was detected in the previous cycle and the current cycle for 60 seconds or more. ·
Relative displacement sensor (brake booster with master cylinder assembly) output value was outside the operating range in the previous cycle and the current cycle for 300 seconds or more. ·
Relative displacement sensor (brake booster with master cylinder assembly) output value is 0.6 mm or more and within 1.5 mm for 60 seconds or more. |
·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C127A64 | Electronic Brake Booster Input Stroke Sensor "A" Signal Plausibility Failure | Relative displacement sensor (brake booster with master cylinder assembly) output signal interrupted for 0.1 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C127A86 | Electronic Brake Booster Input Stroke Sensor "A" Signal (some circuit quantity, reported via serial data) Invalid | Relative displacement sensor (brake booster with master cylinder assembly) malfunction is detected for 1 second or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C127A96 | Electronic Brake Booster Input Stroke Sensor "A" Component Internal Failure | Relative displacement sensor (brake booster with master cylinder assembly) internal malfunction is detected for 0.1 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C127F1C | Electronic Brake Booster Input Stroke Sensor Supply Voltage Circuit Voltage Out of Range | Relative displacement sensor (brake booster with master cylinder assembly) power source voltage (VSK) is less than 4.8 V or more than 5.18 V for 0.08 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C128A11 | Electronic Brake Booster Input Stroke Sensor "B" Circuit Short to Ground | Open in relative displacement sensor (brake booster with master cylinder assembly) signal circuit for 0.2 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C128A15 | Electronic Brake Booster Input Stroke Sensor "B" Circuit Short to Battery or Open | Short in relative displacement sensor (brake booster with master cylinder assembly) signal circuit for 0.2 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C128A64 | Electronic Brake Booster Input Stroke Sensor "B" Signal Plausibility Failure | Relative displacement sensor (brake booster with master cylinder assembly) operation failure is detected for 0.2 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
| C128F64 | Electronic Brake Booster Input Stroke Sensor "A" / "B" Signal Plausibility Failure | Difference between change amounts of relative displacement sensor (brake booster with master cylinder assembly) output 1 (SKS1) and relative displacement sensor (brake booster with master cylinder assembly) output 2 (SKS2) is abnormally large for 0.2 seconds or more. | ·
Wire harness or connector* ·
No. 2 engine room wire* ·
Electric brake booster (brake booster with master cylinder assembly) |
Brake Booster |
*: for RHD
After replacing the electric brake booster (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".
Choose the model to be inspected
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER (for HV Model LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A35 electric brake booster (brake booster with master cylinder assembly) connector.
Disconnect the AR1 No. 2 engine room wire assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 (VSK) - AR1-2 | Always | Below 1 Ω |
| A35-2 (VSK) or AR1-2 - Body ground | Always | 10 kΩ or higher |
| A35-22 (SKS1) - AR1-3 | Always | Below 1 Ω |
| A35-22 (SKS1) or AR1-3 - Body ground | Always | 10 kΩ or higher |
| A35-23 (SKS) - AR1-4 | Always | Below 1 Ω |
| A35-23 (SKS) or AR1-4 - Body ground | Always | 10 kΩ or higher |
| A35-8 (SKG) - AR1-1 | Always | Below 1 Ω |
| A35-8 (SKG) or AR1-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG