If the skid control ECU (brake booster with master cylinder assembly) detects an internal sensor (reaction force pressure sensor, accumulator pressure sensor or servo pressure sensor) malfunction during self-diagnosis, DTCs are stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C057300 | Brake Pressure Sensor "C" Circuit/Open | Data from the sensor is invalid for 0.8 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C05731F | Brake Pressure Sensor "C" Circuit Intermittent | Fluctuation of the sensor signal exceeds the threshold (7.5 MPa (76.5 kgf/cm2, 1088 psi) or more from the previous value) for 0.1 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C057331 | Brake Pressure Sensor "C" No Signal | Communication with the sensor is invalid for 0.2 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C057347 | Brake Pressure Sensor "C" Watchdog / Safety MCU Failure | ECU internal malfunction. (A sensor malfunction is detected by the internal IC.) | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C057396 | Brake Pressure Sensor "C" Component Internal Failure | A malfunction is detected by self-diagnosis function of the sensor. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C057700 | Brake Pressure Sensor "D" Malfunction | Data from the sensor is invalid for 0.2 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C05771F | Brake Pressure Sensor "D" Circuit Intermittent | Fluctuation of the sensor signal exceeds the threshold (7.5 MPa (76.5 kgf/cm2, 1088 psi) or more from the previous value) for 0.1 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C057731 | Brake Pressure Sensor "D" No Signal | Communication with the sensor is invalid for 0.05 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C057796 | Brake Pressure Sensor "D" Component Internal Failure | A malfunction is detected by self-diagnosis function of the sensor. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C05A100 | Brake Pressure Sensor "E" Malfunction | Data from the sensor is invalid for 0.2 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C05A11F | Brake Pressure Sensor "E" Circuit Intermittent | Fluctuation of the sensor signal exceeds the threshold (7.5 MPa (76.5 kgf/cm2, 1088 psi) or more from the previous value) for 0.1 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C05A131 | Brake Pressure Sensor "E" No Signal | Communication with the sensor is invalid for 0.05 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C05A196 | Brake Pressure Sensor "E" Component Internal Failure | A malfunction is detected by self-diagnosis function of the sensor. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C14B01C | Brake Pressure Sensor "D" Power Supply Voltage Circuit Voltage Out of Range | The supplied voltage to the sensor is less than 6.3 V or 7.7 V or more for 0.05 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C14C01C | Servo Pressure Sensor Power Supply Voltage Circuit Voltage Out of Range | The supplied voltage to the sensor is less than 6.3 V or 7.7 V or more for 0.05 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
| C14D01C | Accumulator Pressure Sensor Power Supply Voltage Circuit Voltage Out of Range | The supplied voltage to the sensor is less than 6.3 V or 7.7 V or more for 0.05 seconds or more. | Skid control ECU (brake booster with master cylinder assembly) | Brake |
After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
| Proceed to |
|---|
| NEXT |
NEXT