Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model TMC Made RHD) › from 2020.07
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0432273 BRAKE BOOSTER(for HV Model TMC Made RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model TMC Made RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Skid control ECU (brake booster with master cylinder assembly)
1.

Bleed air

2.

Perform "Reset Memory"

3.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Update ECU security key - (Click here)

NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55815E 3.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 5.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 6.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

a.

Using the GTS, perform the accumulator pressure zero down.

i.

Connect the GTS to the DLC3 with the ignition switch off.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on and enter the following menus: Chassis / Brake / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > Brake > Utility
Tester Display
ECB Utility
50005 435 2617

iv.

Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


v.

Perform "Motor Invalid" according to the display on the GTS.


vi.

Enter the following menus: Chassis / Brake / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > Brake > Utility
Tester Display
ECB Utility
50005 435 2617

vii.

Select "ECB (Electronically Controlled Brake system) Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


viii.

Perform "ECB (Electronically Controlled Brake system) Invalid" according to the display on the GTS.


ix.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



x.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down is not complete.



xi.

Turn the GTS off and turn the ignition switch off.


xii.

Disconnect the GTS from the DLC3.


xiii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL



b.

When the accumulator pressure zero down could not be performed using the GTS.

NOTICE:

If DTCs are output, accumulator pressure zero down may not be complete. In this case, perform the following procedure.


i.
C430220C02
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


With the ignition switch off, release the lock lever and disconnect the brake booster pump assembly connector as shown in the illustration.


ii.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


iii.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down is not complete.



iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL



Hide 7.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 82111 8.REMOVE ENGINE ROOM MAIN WIRE

a.
C429869

Disconnect the connector from the brake booster with master cylinder assembly.


b.

Disengage the clamp.


c.
C429870C01
1.333,2.583 1.573,2.583 true 2.802,2.729 2.865,2.604 2.865,2.604 2.99,2.604 true 2.177,3.042 2.323,3.042 2.323,3.042 2.385,2.875 true 1.615,2.479 1.927,2.635 0.313,0.156 10 false *a 1.979,2.938 2.292,3.094 0.313,0.156 10 false *b 2.198,2.5 2.51,2.656 0.313,0.156 10 false *c 3.021,2.5 3.333,2.656 0.313,0.156 10 false *a
*a Lock Lever
*b Lock Arm
*c Push
V113147

Release the lock lever


Push the lock arm of the connector to release the lock and rotate the lock lever to the position shown in the illustration.


d.
C429871C01
0.875,2.938 0.875,3.177 true 1.969,2.885 2.125,2.885 2.125,2.885 2.438,3.219 true 0.792,3.167 1.104,3.323 0.313,0.156 10 false *a 1.792,2.781 2.104,2.938 0.313,0.156 10 false *b
*a Screwdriver Insertion Point
*b Pre-lock
V113147

Disconnect the connector


Using a screwdriver, release the pre-lock and disconnect the connector from the brake booster with master cylinder assembly as shown in the illustration.


e.

Disengage the clamp to separate the engine room main wire.


Hide 44572C 9.DISCONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C429875

Slide the clip and disconnect the No. 2 brake actuator hose from the brake booster with master cylinder assembly.


Hide 10.DISCONNECT BRAKE LINE

a.
C432449

Disengage the 3 clamps to separate the 3 brake lines from the No. 4 brake tube clamps.


b.

Using a union nut wrench, disconnect the 3 brake lines from the brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




Hide 47101A 12.REMOVE BRAKE PEDAL RETURN SPRING

Hide 47210L 14.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C429882C01
2.385,4.146 2.385,3.813 false 1.354,2.906 1.354,2.49 1.354,2.49 1.188,2.49 false 0.625,3.469 0.625,3.052 0.625,3.052 0.458,3.052 false 1.771,2.781 2.104,2.781 false 0.25,4.031 0.25,3.698 false 1.792,3 2.125,3 false 0.99,2.406 1.302,2.563 0.313,0.156 10 false *1 2.167,2.719 2.479,2.875 0.313,0.156 10 false *2 0.188,4.063 0.5,4.219 0.313,0.156 10 false *3 0.281,2.979 0.594,3.135 0.313,0.156 10 false *4 2.323,4.156 2.635,4.313 0.313,0.156 10 false *5 2.156,2.927 2.469,3.083 0.313,0.156 10 false *6
*1 Skid Control ECU
*2 No. 1 Reservoir Hose
*3 Brake Master Cylinder Push Rod Clevis
*4 Boot
*5 Master Cylinder Reservoir Assembly
*6 Brake Actuator Bracket


Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Be careful not to allow any brake fluid to enter the connector.




Hide 44785 15.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the brake booster with master cylinder assembly.