Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C124A00  ECM Communication  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) stores identification information sent from other ECUs when the vehicle is shipped from the factory and changes the control constant for each system (ABS, VSC, TRC, etc.) based on the identification information.

NOTICE:

DTC C124A00 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from those stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C124A00 ECM Communication Either of the following is detected:
·

Identification information sent from other ECUs does not match with the value stored when shipped from the factory.

·

Identification information sent from other ECUs is not stored when shipped from the factory.


·

Other ECUs are not installed correctly

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


PROCEDURE

1.CHECK PART NUMBER
a.

Check that the proper hybrid vehicle control ECU and main body ECU (multiplex network body ECU) are installed.

OK:

Proper ECUs are installed.



b.

Check if the hybrid vehicle control ECU and main body ECU (multiplex network body ECU) were replaced before the DTC was recorded.

OK:

ECUs were not replaced.



Result:
Result Proceed to
OK A
NG (A proper hybrid vehicle control ECU is not installed and/or the hybrid vehicle control ECU was replaced.) B
NG (A proper main body ECU (multiplex network body ECU) is not installed and/or the main body ECU (multiplex network body ECU) was replaced.) C



A

2.SYSTEM INFORMATION MEMORIZATION

B

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

2.SYSTEM INFORMATION MEMORIZATION
a.

Perform system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560
Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554
HINT:

After performing "Reset Memory" using the GTS to clear the memorized value of the skid control ECU (brake booster with master cylinder assembly), DTC C124A00 will be stored until system information memorization is performed.



Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C124A00 is output A
C124A00 is not output B



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

END