Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C12C014  Brake System Control Module Power Supply Voltage Circuit Short to Ground or Open  C14DA14  ABS Solenoid Supply Voltage Circuit Short to Ground or Open  C14DD14  Brake Pressure Control solenoid Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake booster with master cylinder assembly) power source voltage drops, or there is insufficient voltage to operate the main relay, the skid control ECU (brake booster with master cylinder assembly) will store these DTCs.

If the auxiliary battery voltage is temporarily low, these DTCs may be stored.

HINT:

DTC C125600 (Accumulator Low Pressure) may also be memorized if there is a drop in power source voltage.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C12C014 Brake System Control Module Power Supply Voltage Circuit Short to Ground or Open Either of the following is detected:
·

The voltage of IGR or IGP is 9.5 V or less for 10 seconds or more.

·

The speed sensor power voltage is invalid for 60 seconds or more.


·

Any of the following is detected when the ECU internal voltage is 6.92 V or less:

-

The relay output voltage is less than 3.5 V for 0.05 seconds or more, when the main relay operation command is on.

-

The stroke sensor value invalid for 0.2 seconds or more.

-

The reaction force pressure sensor value invalid for 0.2 seconds or more.

-

The servo pressure sensor power source voltage is 6.29 V or less, or 7.64 V or more for 0.06 seconds or more.

-

The servo pressure sensor value invalid for 0.2 seconds or more.

-

The reaction force pressure sensor power source voltage is 6.29 V or less, or 7.64 V or more for 0.06 seconds or more.



·

When the ECU internal voltage is 8.3 V or less, the accumulator pressure sensor value is invalid for 0.8 seconds or more.

·

Either of the following is detected when the ECU internal voltage is 6.9 V or less:

-

When the accumulator pressure sensor value is 15 MPa (153 kgf/cm2, 2176 psi) or less, the pump motor does not operate for 1 second or more.

-

Both the motor relay 1 and 2 cannot be operated for 0.2 seconds or more.



·

Improperly connected connector, deformation or corrosion of terminals

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (brake booster with master cylinder assembly)

·

Wire harness or connector


Brake
C14DA14 ABS Solenoid Supply Voltage Circuit Short to Ground or Open Either of the following is detected when the BS voltage of the ABS unit is 9.1 V or less:
·

The brake is not applied for 3 seconds or more.

·

The brake is applied for 0.05 seconds or more.


·

Improperly connected connector, deformation or corrosion of terminals

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (brake booster with master cylinder assembly)

·

Wire harness or connector


Brake
C14DD14 Brake Pressure Control solenoid Supply Voltage Circuit Short to Ground or Open Either of the following is detected when the BS terminal voltage is 9.1 V or less:
·

The brake is not applied for 3 seconds or more.

·

The brake is applied for 0.05 seconds or more.


·

Improperly connected connector, deformation or corrosion of terminals

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (brake booster with master cylinder assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC
a.

Check that no main relay malfunction DTCs are output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
Only C12C014, C14DA14 or C14DD14 is output A
None of the above conditions are met B



A

2.CHECK AUXILIARY BATTERY

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Ignition switch ON 11 to 14 V
Auxiliary battery Ignition switch ON (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-15 (+BI1) - Body ground Always 11 to 14 V
A38-5 (+BI2) - Body ground Always 11 to 14 V
A38-52 (BS) - Body ground Always 11 to 14 V
A38-23 (IGR) - Body ground Ignition switch ON 11 to 14 V
A38-9 (IGP) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-26 (GND1) - Body ground Always Below 1 Ω
A38-39 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

5.CLEAR DTC
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C12C014, C14DA14 and C14DD14 are not output A
C12C014, C14DA14 or C14DD14 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY