Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C134951  Pressure Holding Solenoid Valve Learning Not Programmed  C134954  Pressure Holding Solenoid Valve Learning Missing Calibration  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) stores the individual characteristic of each holding solenoid built into the brake actuator assembly. Based on the stored information, the skid control ECU (brake booster with master cylinder assembly) calibrates the individual differences and controls systems.

The skid control ECU (brake booster with master cylinder assembly) receives the park (P) signal from the hybrid vehicle control ECU through the CAN communication system.

These DTCs are cleared when the ABS holding solenoid valve learning results are normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C134951 Pressure Holding Solenoid Valve Learning Not Programmed The ABS holding solenoid valve learning value is not stored. Perform ABS holding solenoid valve learning and check for DTCs. If no DTCs are output again, the valve is normal. Brake
C134954 Pressure Holding Solenoid Valve Learning Missing Calibration The ABS holding solenoid valve learning value cannot be obtained.
·

Perform ABS holding solenoid valve learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

Skid control ECU (brake booster with master cylinder assembly)

·

Brake actuator assembly


Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


HINT:

Before performing linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization, DTC C124A00 will be output.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Check that DTCs other than C134951 and C134954 are not output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
Only C134951 or C134954 is output A
None of the above conditions are met B



A

3.PERFORM AIR BLEEDING

B

3.PERFORM AIR BLEEDING

NEXT

4.PERFORM ABS HOLDING SOLENOID VALVE LEARNING
4.PERFORM ABS HOLDING SOLENOID VALVE LEARNING
a.

Turn the ignition switch off.


b.

Check and ensure the following conditions required for performing ABS holding solenoid valve learning and then perform ABS holding solenoid valve learning.

HINT:

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


Chassis > Brake > Utility
Tester Display
ECB Utility
50005 435 2617
1.

The auxiliary battery voltage is 11 to 15.5 V when the ignition switch ON (READY).

2.

The brake actuator assembly is not hot.

3.

The hybrid control system is not malfunctioning.

4.

The shift state indicator shows that the vehicle shift state is park (P).

5.

The READY light in the combination meter assembly is illuminated.

6.

The brake pedal is not depressed.

7.

The parking brake is released.


NOTICE:

Learning will be performed in the order of linear solenoid valve offset learning and then ABS holding solenoid valve learning.



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C134951 and C134954 are not output A
C134951 or C134954 is output B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY