Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C142771  ABS Pump Motor Actuator Stuck  


DESCRIPTION

When the ignition switch ON (READY), the stop light switch assembly off and the vehicle speed is 20 km/h (12 mph) or more, the skid control ECU (brake booster with master cylinder assembly) performs a self-diagnosis of the ABS motor relay circuit during the initial check of the actuator.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C142771 ABS Pump Motor Actuator Stuck The pump motor built into the brake actuator assembly is not operating correctly.
·

Wire harness or connector

·

Pump motor or pump motor circuit built into the brake actuator assembly


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

Select the Active Test on the GTS.

Chassis > Brake > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard.
Chassis > Brake > Active Test
Tester Display
Motor Relay
50004 435 11

b.

Check the operating sound of the ABS motor relay when operating it with the GTS.


Result:
Result Proceed to
The operating sound is heard. A
The operating sound is not heard. B



A

2.CLEAR DTC

B

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C142771 is not output A
C142771 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A40 brake actuator assembly connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-40 (+BM) - A40-13 (+BM) Always Below 1 Ω
A38-40 (+BM) or A40-13 (+BM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-1 (MGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

6.CLEAR DTC
a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A40 brake actuator assembly connector.


c.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC
7.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C142771 is not output A
C142771 is output B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY