Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  P05FF62  Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure  


DESCRIPTION

If the skid control ECU (brake booster with master cylinder assembly) detects an inconsistency between the brake pedal stroke sensor assembly signal and reaction force pressure sensor signal, DTC P05FF62 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P05FF62 Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure The difference between brake pedal stroke sensor assembly output value and reaction force pressure sensor output value is above the threshold for a certain period of time.
·

Brake actuator (brake booster with master cylinder assembly)

·

Brake pedal stroke sensor assembly


Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake actuator (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA
a.

Interview the customer to check the vehicle conditions when the brake system warning light (red indicator) and brake system warning light (yellow indicator) illuminated.


b.

Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>FREEZE FRAME DATA

Chassis > Brake > Trouble Codes
50001 435

HINT:
·

Freeze Frame Data is only stored once when a DTC is stored.

·

If other DTCs are output, repair any malfunctions related to those DTCs first, and then reproduce the conditions that caused DTC P05FF62 to be stored based on the interview with the customer.



Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (STROKE SENSOR, STROKE SENSOR2)
2.READ VALUE USING GTS (STROKE SENSOR, STROKE SENSOR2)
a.

Turn the ignition switch off.


b.

Mount a pedal effort gauge.


c.

Disconnect the A30 brake booster pump assembly connector.


d.

Depress the brake pedal 10 times or more until it becomes hard.

HINT:

Depressing the brake pedal with the connector of the brake booster pump assembly disconnected drops the accumulator pressure to approximately 0 MPa.



e.

Connect an LSPV gauge set.


f.

Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.


g.

With the brake pedal released, confirm the brake pedal stroke sensor assembly output voltage.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor 2 Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Chassis > Brake > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 435 207,208
NOTICE:

Check the wheel cylinder pressure with the switching solenoid (SSA, SGH) off and an accumulator pressure of 0 MPa.


Standard Voltage:
Front
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Stroke Sensor 2
[V]
Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
200 (20, 45.0) 1.23 to 1.93 3.07 to 3.77 0.06 to 2.06 (0.6 to 21.0, 9 to 299)
500 (51, 112.4) 1.42 to 2.12 2.88 to 3.58 2.09 to 4.09 (21.3 to 41.7, 303 to 593)

Rear
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Stroke Sensor 2
[V]
Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
200 (20, 45.0) 1.23 to 1.93 3.07 to 3.77 0.06 to 2.06 (0.6 to 21.0, 9 to 299)
500 (51, 112.4) 1.42 to 2.12 2.88 to 3.58 2.09 to 4.09 (21.3 to 41.7, 303 to 593)



Result:
Proceed to
OK
NG



OK

3.REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY

NG

3.REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Reconnect the A30 brake booster pump assembly connector.



d.

Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560
Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

4.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
P05FF62 is not output A
P05FF62 is output B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY