Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) Y

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:

*: Use the GTS.


PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS

Result:
Proceed to
NEXT



NEXT

3.CHECK DTC AND FREEZE FRAME DATA*
3.CHECK DTC AND FREEZE FRAME DATA*
a.

Check and record DTCs and Freeze Frame Data.

i.

Check and record DTCs.

Chassis > Brake > Trouble Codes
50001 435

ii.

Check and record Freeze Frame Data.



b.

Clear the DTCs and Freeze Frame Data.

Chassis > Brake > Clear DTCs
50002 435

c.

Reconfirm the DTCs.

i.

Reconfirm the DTCs based on the recorded DTCs and Freeze Frame Data.

Chassis > Brake > Trouble Codes
50001 435
HINT:
·

When CAN communication system DTCs are output, repair the CAN communication system first.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If DTC U007488, U010087, U010187, U012587, U012687 and/or U015187 are among the CAN communication DTCs that are output, first use the Data List to check for a momentary open circuit.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CHECK FOR INTERMITTENT PROBLEMS

·

If the GTS cannot communicate with the skid control ECU (brake actuator assembly), inspect the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If there is no response from the skid control ECU (brake actuator assembly), inspect the +BS and/or IGR circuit of the skid control ECU (brake actuator assembly).

C137BA2: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>C137BA2

C137BA3: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>C137BA3





Result:
Result Proceed to
DTCs are output A
DTCs are not output (Problem symptom does not occur) B
DTCs are not output (Problem symptom occurs) C



A

4.DIAGNOSTIC TROUBLE CODE CHART

B

5.SYMPTOM SIMULATION

C

6.PROBLEM SYMPTOMS TABLE
4.DIAGNOSTIC TROUBLE CODE CHART

NEXT

7.CIRCUIT INSPECTION*
5.SYMPTOM SIMULATION

Result:
Proceed to
NEXT



NEXT

6.PROBLEM SYMPTOMS TABLE
6.PROBLEM SYMPTOMS TABLE

NEXT

7.CIRCUIT INSPECTION*
7.CIRCUIT INSPECTION*
Result:
Proceed to
NEXT



NEXT

8.IDENTIFICATION OF PROBLEM
8.IDENTIFICATION OF PROBLEM
Result:
Proceed to
NEXT



NEXT

9.REPAIR OR REPLACEMENT
9.REPAIR OR REPLACEMENT
Result:
Proceed to
NEXT



NEXT

10.RECONFIRM DTC*
10.RECONFIRM DTC*
a.

Use the GTS, clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Check if the same DTCs are output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

11.CONFIRMATION TEST*

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

11.CONFIRMATION TEST*
Result:
Proceed to
NEXT



NEXT

END