Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › 2020.07–2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C137BA2  Brake System Control Module "A" System Voltage System Voltage Low  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the auxiliary battery or alternator circuit, etc.

The DTC is cleared when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C137BA2 Brake System Control Module "A" System Voltage System Voltage Low Any of the following is detected:
·

When the +BS terminal voltage is below 9.5 V, the power source voltage for all speed sensors is continuously low for 60 seconds or more.

·

After the +BS terminal voltage is below 9.5 V continuously for 3 seconds or more, the +BS terminal voltage is below 9.5 V continuously for 7 seconds or more at a vehicle speed exceeding 3 km/h (2 mph).

·

When the +BS terminal voltage is 9.5 V or higher and the vehicle speed exceeds 15 km/h (9 mph), the IGR terminal voltage is 10 V or less continuously for 60 seconds or more.

·

When the +BS terminal voltage is below 9.5 V and the solenoid relay is ON, the relay contact is OFF continuously for 1.22 seconds or more.

·

When the +BS terminal voltage is below 9.5 V, motor fail-safe relay overcurrent continues for 1.05 seconds or more.


·

Auxiliary battery

·

Charging system

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


Brake

WIRING DIAGRAM

C416042E05
5.969,1.271 6.427,1.469 0.458,0.198 10 false +BS 5.969,2.031 6.281,2.229 0.313,0.198 10 false IGR 5.969,2.865 6.583,3.063 0.615,0.198 10 false GND1 5.656,1.167 5.969,1.365 0.313,0.198 10 false 38 5.667,1.938 5.979,2.135 0.313,0.198 10 false 12 5.688,2.76 6,2.958 0.313,0.198 10 false 25 5.542,3.917 6,4.115 0.458,0.198 10 false A36 5.531,4.083 7.063,4.615 1.531,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 3.75,1.406 4.979,1.604 1.229,0.198 10 false ABS NO. 2 3.583,2.188 4.813,2.385 1.229,0.198 10 false ECU-IGR NO. 3 1.344,1.26 2.927,1.573 1.583,0.313 10 false from Auxiliary Battery 1.365,2.031 2.969,2.219 1.604,0.188 10 false from IGR-NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION



PROCEDURE

1.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM OR AUXILIARY BATTERY

2.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-38 (+BS) - Body ground Always 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-12 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-25 (GND1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CLEAR DTC

Pre-procedure1

a.

Reconnect the A36 skid control ECU (brake actuator assembly) connector.


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

c.

Press the DTC clear button.


Post-procedure1

d.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Result:
Result Proceed to
C137BA2 is not output A
C137BA2 is output B



A

B