Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › 2020.07–2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C051223  Right Rear Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C05121F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>C05121F

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C051223 Right Rear Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more.


·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Sensor installation

·

Skid control sensor wire RH

·

Wire harness and connector

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Skid control ECU (brake actuator assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C210569C18
1.208,1.365 0.979,1.167 false 0.833,1.833 1.25,2.083 0.417,0.25 10 false *b 2.344,1.833 2.677,2.083 0.333,0.25 10 false *c 1.26,1.313 1.594,1.49 0.333,0.177 10 false *a
*a No clearance
*b Correct
*c Incorrect


Turn the ignition switch off.


b.

Check the rear speed sensor RH installation.

OK:

There is no clearance between the rear speed sensor RH and the rear axle hub and bearing assembly RH.


HINT:

The rear speed sensor rotor RH and rear speed sensor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor rotor RH needs to be replaced, replace the rear axle hub and bearing assembly RH with rear speed sensor RH.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (RR WHEEL SPEED)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

2.READ VALUE USING GTS (RR WHEEL SPEED)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RR Wheel Speed
50003 435 15

b.

Drive the vehicle and perform a road test.


c.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT SKID CONTROL SENSOR WIRE RH
3.INSPECT SKID CONTROL SENSOR WIRE RH
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the i1 and iO1 skid control sensor wire RH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (RR+) - iO1-2 (RR+) Always Below 1 Ω
i1-2 (RR+) or iO1-2 (RR+) - Body ground and other terminals Always 10 kΩ or higher
i1-1 (RR-) - iO1-1 (RR-) Always Below 1 Ω
i1-1 (RR-) or iO1-1 (RR-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE RH - BRAKE ACTUATOR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE RH - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
iO1-2 (RR+) - A36-16 (RR+) Always Below 1 Ω
iO1-2 (RR+) or A36-16 (RR+) - Body ground and other terminals Always 10 kΩ or higher
iO1-1 (RR-) - A36-15 (RR-) Always Below 1 Ω
iO1-1 (RR-) or A36-15 (RR-) - Body ground and other terminals Always 10 kΩ or higher


HINT:

The rear speed sensor RH is incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH needs to be replaced, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR