Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C14FE14  Steering Angle Sensor Supply Voltage Circuit Circuit Short to Ground or Open  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) receives a power supply malfunction signal from the steering sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C14FE14 Steering Angle Sensor Supply Voltage Circuit Circuit Short to Ground or Open When the +BS terminal voltage is from 9.5 to 17.4 V, a steering sensor power supply malfunction signal is received from the steering sensor.
·

Steering sensor

·

Wire harness and connector


Brake

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC
a.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

Procedure1

c.

Check if the same DTC is output.


Post-procedure1

d.

None


Result:
Result Proceed to
C14FE14 is not output A
C14FE14 is output B



A

B

3.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)
3.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the H39 steering sensor connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

d.

Turn the ignition switch to ON.


Procedure1

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H39-9 (IGR) - Body ground Ignition switch ON 11 to 14 V



Post-procedure1

f.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H39-4 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H39-6 (ESS) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR