Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  U007488  Control Module Communication Bus "B" Off Bus Off  U010087  Lost Communication with ECM/PCM "A" Missing Message  U010187  Lost Communication with TCM Missing Message  U012587  Lost Communication with Multi-axis Acceleration Sensor Module Missing Message  U012687  Lost Communication with Steering Angle Sensor Module Missing Message  U015187  Lost Communication with Restraints Control Module Missing Message  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the ECM, steering sensor and airbag sensor assembly via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U007488 Control Module Communication Bus "B" Off Bus Off Any of the following is detected:
·

A bus OFF state occurs once or more within 0.1 seconds, 10 times in succession.

·

When the +BS terminal voltage is between 9.5 and 17.4 V, a delay in receiving data from the yaw rate and acceleration sensor (airbag sensor assembly) and steering sensor continues for 1 second or more.

·

When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds:

-

A delay in receiving data from the yaw rate and acceleration sensor (airbag sensor assembly) and steering sensor occurs once or more within 5 seconds.



CAN communication system Brake
U010087 Lost Communication with ECM/PCM "A" Missing Message When the +BS terminal voltage is between 9.5 and 17.4 V and the vehicle speed exceeds 15 km/h (9 mph), data cannot be received from the ECM for 2 seconds or more.
·

CAN communication system

·

ECM

·

Skid control ECU (brake actuator assembly)


Brake
U010187 Lost Communication with TCM Missing Message When the +BS terminal voltage is between 9.5 and 17.4 V and the vehicle speed exceeds 15 km/h (9 mph), data cannot be received from the TCM (ECM) for 2 seconds or more.
·

CAN communication system

·

TCM

·

Skid control ECU (brake actuator assembly)


Brake
U012587 Lost Communication with Multi-axis Acceleration Sensor Module Missing Message Either of the following is detected:
·

When the +BS terminal voltage is between 9.5 and 17.4 V, data from the acceleration sensor cannot be received for 1 second or more.

·

When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds:

-

Data from the acceleration sensor cannot be received once or more within 5 seconds.



·

CAN communication system

·

Acceleration sensor (airbag sensor assembly)

·

Skid control ECU (brake actuator assembly)


Brake
U012687 Lost Communication with Steering Angle Sensor Module Missing Message Either of the following is detected:
·

When the +BS terminal voltage is between 9.5 and 17.4 V, data from the steering sensor cannot be received for 1 second or more.

·

When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds:

-

Data from the steering sensor cannot be received once or more within 5 seconds



·

CAN communication system

·

Steering sensor

·

Skid control ECU (brake actuator assembly)


Brake
U015187 Lost Communication with Restraints Control Module Missing Message When the +BS terminal voltage is between 9.5 and 17.4 V and the vehicle speed exceeds 7 km/h (4 mph), data cannot be received from the airbag sensor assembly for 5 seconds or more.
·

CAN communication system

·

Airbag sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake

PROCEDURE

1.CLEAR DTC
a.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435
Result:
Result Proceed to
Any CAN communication system relating DTCs are output A
None of the above conditions are met B


HINT:

If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for electronically controlled brake system) after the CAN communication system returns to normal.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>HOW TO PROCEED WITH TROUBLESHOOTING




A

B