This DTC is stored when CXPI communication between the semiconductor power integration ECU, power distribution box assembly, windshield wiper relay assembly or light control LED ECU and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B235287 | Power Integration No.1 System Missing Message | No communication between semiconductor power integration ECU and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Semiconductor power integration ECU ·
Harness or connector |
| B235587 | Power Distribution Box Missing Message | No communication between power distribution box assembly and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Power distribution box assembly |
| B235787 | Wiper Module Missing Message | No communication between windshield wiper relay assembly and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Windshield wiper relay assembly ·
Harness or connector |
| B235887 | Smart LDM Left Missing Message | No communication between light control LED ECU LH and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Light control LED ECU LH ·
Harness or connector |
| B235987 | Smart LDM Right Missing Message | No communication between light control LED ECU RH and main body ECU (multiplex network body ECU) for 10 seconds or more | ·
Main body ECU (multiplex network body ECU) ·
Light control LED ECU RH ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Clear the DTCs.
Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result |
|---|
| NEXT |
NEXT
Check for DTCs.
Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B235287, B235587, B235787, B235887 and B235987 is output | A |
| DTC B235287, B235787, B235887 and B235987 is output | B |
| DTC B235587 is output | C |
| DTC B235287 is output | D |
| DTC B235787 is output | E |
| DTC B235887 is output | F |
| DTC B235987 is output | G |
| DTC is not output | H |
A
B
C
D
E
F
G
H
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the power distribution box assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Disconnect the 4D power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-22 (CXPI) - 4D-5 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the power distribution box assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Disconnect the 4D power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-22 (CXPI) - 4D-5 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4D power distribution box assembly connector.
Disconnect the A49 windshield wiper relay assembly connector.
Disconnect the A4 light control LED ECU LH connector.
Disconnect the A5 light control LED ECU RH connector.
Disconnect the A86 semiconductor power integration ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-5 - A86-8 (CXPI) | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| 4D-5 - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4B and 4C power distribution box assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-41 (GND1) - Body ground | Always | Below 1 Ω |
| 4B-44 (GND2) - Body ground | Always | Below 1 Ω |
| 4B-36 (GND3) - Body ground | Always | Below 1 Ω |
| 4C-25 (GND4) - Body ground | Always | Below 1 Ω |
Connect the cable to the negative (-) auxiliary battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4G-1 (+B1) - Body ground | Ignition switch off | 11 to 14 V |
| 4F-1 (+B2) - Body ground | Ignition switch off | 11 to 14 V |
| 4H-1 (+B3) - Body ground | Ignition switch off | 11 to 14 V |
| 4D-23 (+B4) - Body ground | Ignition switch off | 11 to 14 V |
| 4B-11 (IGR) - Body ground | Ignition switch ON | 11 to 14 V |
| 4C-17 (IGP) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A86 semiconductor power integration ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A86-26 (GND1) - Body ground | Always | Below 1 Ω |
Connect the cable to the negative (-) auxiliary battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A85-1 (+B) - Body ground | Ignition switch ON | 8 to 14 V |
| A86-20 (IG) - Body ground | Ignition switch ON | 8 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the 4D power distribution box assembly connector.
Disconnect the A86 semiconductor power integration ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A86-8 (CXPI) - 4D-5 | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| A86-8 (CXPI) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A49 and A50 windshield wiper relay assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-5 (ES) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A50-6 (IGWS) - Body ground | Ignition switch ON | 11 to 14 V |
| A50-8 (+B) - Body ground | Ignition switch ON or less than approximately 60 seconds after ignition switch turned off | 11 to 14 V |
| Approximately 60 seconds or more after ignition switch turned off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A49 windshield wiper relay assembly connector.
Disconnect the 4D power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-4 (MPX1) - 4D-5 | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| A49-4 (MPX1) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU (for LHD)>REMOVAL
for RHD: Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU (for RHD)>REMOVAL
NG
Disconnect the A4 light control LED ECU LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-5 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-2 (LO) - Body ground | Taillight on → off | 9.5 to 14 V → Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A4 light control LED ECU LH connector.
Disconnect the 4D power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-1 (AT1) - 4D-5 | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| A4-1 (AT1) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A5 light control LED ECU RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-5 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-2 (LO) - Body ground | Taillight on → off | 9.5 to 14 V → Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A5 light control LED ECU RH connector.
Disconnect the 4D power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-1 (AS1) - 4D-5 | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| A5-1 (AS1) - Body ground | Cable disconnected from negative (-) auxiliary battery terminal | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG