Home › Drivetrain › K320 (MULTIDRIVE / CVT) › PARK / NEUTRAL POSITION SWITCH › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422064 PARK / NEUTRAL POSITION SWITCH N

K320 MULTIDRIVE / CVT  PARK / NEUTRAL POSITION SWITCH  ADJUSTMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the park/neutral position switch assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Air intake system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
If possible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
If impossible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Update ECU security key Vehicle control history (RoB) are stored (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 33820B 4.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 84540 5.ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C429229

Disconnect the park/neutral position switch assembly connector.


b.
C429230C02
1.365,1.073 1.75,1.073 true 1.771,0.958 1.969,1.188 0.198,0.229 10 true *a
*a Piece of Wood or Equivalent


Using a piece of wood or equivalent to secure the transmission control shaft lever to prevent it from rotating, remove the nut, washer and transmission control shaft lever from the manual valve lever shaft.

NOTICE:
C432070C02
1.458,0.417 1.667,0.167 1.667,0.167 1.833,0.167 true 1.833,1.323 2.333,0.583 2.333,0.583 2.5,0.583 true 1.479,1.833 1.896,1.833 true 1.885,0.104 2.167,0.344 0.281,0.24 10 false *1 2.542,0.521 2.823,0.76 0.281,0.24 10 false *2 1.271,1.771 1.469,1.917 0.198,0.146 10 true *3
*1 Transmission Control Shaft Lever
*2 Manual Valve Link Lever Sub-assembly
*3 Manual Valve


If the transmission control shaft lever is not secured when loosening the nut, the manual valve link lever sub-assembly may separate from the manual valve.



c.
C429231

Loosen the 2 bolts of the park/neutral position switch assembly.


d.
C432799C01
2.542,0.469 2.948,0.417 2.948,0.417 2.542,0.635 true 3,0.302 3.198,0.521 0.198,0.219 10 false *a
*a Protrusion


Align the protrusions of the park/neutral position switch assembly as shown in the illustration.


e.

Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


f.

Install the transmission control shaft lever to the manual valve lever shaft with the washer and nut.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


g.

Connect the park/neutral position switch assembly connector.


Hide 33820B 6.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 84540 8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Hide 9. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART