Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (for HV Model without Entry and Start System) › from 2020.07
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424981 IMMOBILISER SYSTEM(for HV Model without Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(for HV Model without Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The transponder key ECU assembly blinks the security indicator light (combination meter assembly) when the immobiliser is set (no key is in the ignition key cylinder).

·

The main body ECU (multiplex network body ECU) blinks the security indicator light (combination meter assembly) when the theft deterrent system is in the arming preparation state or alarm sounding state.*1

*1: w/ Theft Deterrent System



WIRING DIAGRAM

B506679E13
0.781,1.313 1.229,1.542 0.448,0.229 10 false H6 0.781,1.125 1.229,1.354 0.448,0.229 10 false 23 2.802,1.313 3.25,1.542 0.448,0.229 10 false H7 2.833,1.115 3.281,1.344 0.448,0.229 10 false 7 1.104,1.323 1.552,1.552 0.448,0.229 10 false ES 2.458,1.313 2.906,1.542 0.448,0.229 10 false LP 0.667,2.156 2.938,2.615 2.271,0.458 10 false Security Indicator Light (Combination Meter Assembly) 0.208,5.323 2.188,5.583 1.979,0.26 10 false *1: w/ Theft Deterrent System 5.448,2.125 5.896,2.354 0.448,0.229 10 false H74 5.448,2.302 6.51,2.708 1.063,0.406 10 false Transponder Key ECU Assembly 5.208,4.635 5.656,4.865 0.448,0.229 10 false H4 5.219,4.802 6.854,5.302 1.635,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 4.188,3.677 4.635,3.906 0.448,0.229 10 false *1 5.427,1.208 5.875,1.438 0.448,0.229 10 false IND 5.198,1.198 5.646,1.427 0.448,0.229 10 false 8 5.458,3.729 5.906,3.958 0.448,0.229 10 false IND 5.219,3.719 5.667,3.948 0.448,0.229 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light (combination meter assembly) ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light (combination meter assembly) ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Security Indicator
50004 449 1

Result:
Result Proceed to
Security indicator light (combination meter assembly) operation is normal when performing the "Main Body" and "Immobiliser" Active Test A
·

Security indicator light (combination meter assembly) operation is not normal when performing the "Immobiliser" Active Test

·

Security indicator light (combination meter assembly) operation is normal when performing the "Main Body" Active Test


B
·

Security indicator light (combination meter assembly) operation is normal when performing the "Immobiliser" Active Test

·

Security indicator light (combination meter assembly) operation is not normal when performing the "Main Body" Active Test


C
Security indicator light (combination meter assembly) operation is not normal when performing the "Main Body" and "Immobiliser" Active Test D



A

2.CHECK SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) OPERATION

B

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

5.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
2.CHECK SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) OPERATION
a.

When the immobiliser is set, check that the security indicator light (combination meter assembly) blinks.*1

OK:

The security indicator light (combination meter assembly) blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light (combination meter assembly) is on.*2

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

OK:

The security indicator light (combination meter assembly) is on.



Result:
Result Proceed to
Both *1 and *2 are OK A
*1 is NG (*2 is OK) B
*2 is NG (*1 is OK) C
Both *1 and *2 are NG D



A

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

D

REPLACE SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the H7 security indicator light (combination meter assembly) connector.


b.

Disconnect the H74 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-8 (IND) - H7-7 (LP) Always Below 1 Ω
H74-8 (IND) or H7-7 (LP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H7 security indicator light (combination meter assembly) connector.


b.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-7 (IND) - H7-7 (LP) Always Below 1 Ω
H4-7 (IND) or H7-7 (LP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the H7 security indicator light (combination meter assembly) connector.


b.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-7 (IND) - H7-7 (LP) Always Below 1 Ω
H4-7 (IND) or H7-7 (LP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - BODY GROUND)
a.

Disconnect the H6 security indicator light (combination meter assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-23 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR