Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM J

G16E-GTS ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned on (IG), the battery voltage is applied to IGSW of the ECM. When the transistor in the MREL circuit operates, current flows from the battery to ground through the drive circuit of the EFI-MAIN NO. 1 relay, thus operating the relay which supplies power to the +B and +B2 terminals of the ECM.

WIRING DIAGRAM

A468625E03
0.552,4.813 1.469,5.01 0.917,0.198 10 false Battery 0.438,3.833 1.51,4.031 1.073,0.198 10 false ENG 1.885,2.156 2.802,2.354 0.917,0.198 10 false IGP-MAIN 0.75,0.656 1.667,0.854 0.917,0.198 10 false AM1 5.802,3.646 6.719,3.844 0.917,0.198 10 false MREL 5.844,2.865 6.76,3.063 0.917,0.198 10 false +B 5.844,3.281 6.76,3.479 0.917,0.198 10 false +B2 5.844,1.875 6.76,2.073 0.917,0.198 10 false IGP 6.115,4.854 6.917,5.396 0.802,0.542 10 false ECM 6.094,4.667 6.521,4.854 0.427,0.188 10 false A106 4.917,2.115 5.833,2.313 0.917,0.198 10 false INJ 5.656,2.771 5.896,2.979 0.24,0.208 10 false 9 5.583,3.219 5.823,3.427 0.24,0.208 10 false 35 5.563,3.646 5.802,3.854 0.24,0.208 10 false 15 5.854,4.25 6.771,4.448 0.917,0.198 10 false E1 5.563,4.167 5.802,4.375 0.24,0.208 10 false 10 5.635,1.875 5.875,2.083 0.24,0.208 10 false 2 3.313,4.042 4.646,4.365 1.333,0.323 10 false EFI-MAIN NO.1 3.281,3.635 3.521,3.844 0.24,0.208 10 false 1 3.271,3.198 3.51,3.406 0.24,0.208 10 false 3 4.125,3.625 4.365,3.833 0.24,0.208 10 false 2 4.115,3.188 4.354,3.396 0.24,0.208 10 false 5 1.76,3.49 3.094,3.813 1.333,0.323 10 false EFI-MAIN NO.1 3.656,2.708 4.573,2.906 0.917,0.198 10 false IGP 4.083,2.271 4.323,2.479 0.24,0.208 10 false 1 3.271,2.292 3.51,2.5 0.24,0.208 10 false 2 4.094,1.875 4.333,2.083 0.24,0.208 10 false 5 3.281,1.875 3.521,2.083 0.24,0.208 10 false 3 0.406,1.302 1.49,1.573 1.083,0.271 10 false INP STD NO.1-3 1.635,1.021 3.167,1.438 1.531,0.417 10 false Ignition or Starter Switch Assembly*2 1.646,0.844 2.563,1.042 0.917,0.198 10 false H54 1.51,0.365 1.75,0.573 0.24,0.208 10 false 7 2.729,0.354 2.969,0.563 0.24,0.208 10 false 8 3.375,0.365 3.615,0.573 0.24,0.208 10 false *2 4.99,0.385 5.229,0.594 0.24,0.208 10 false *1 5.323,0.875 6.24,1.073 0.917,0.198 10 false H45 5.323,1.063 7.135,1.552 1.813,0.49 10 false Certification ECU (Smart Key ECU Assembly)*1 5.823,0.479 6.74,0.677 0.917,0.198 10 false IGPD 5.49,0.365 5.729,0.573 0.24,0.208 10 false 24 1.719,4.927 4.719,5.188 3,0.26 10 false *1: w/ Entry and Start System 1.708,5.271 4.708,5.531 3,0.26 10 false *2: w/o Entry and Start System 2.396,0.354 2.635,0.563 0.24,0.208 10 false IG1 1.708,0.354 2.073,0.563 0.365,0.208 10 false AM1 6.375,3.729 6.927,3.896 0.552,0.167 10 false IC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A106-10(E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IGP TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGP TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A106-2(IGP) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT EFI-MAIN NO. 1 RELAY

NG

6.INSPECT IGP RELAY
3.INSPECT EFI-MAIN NO. 1 RELAY
a.

Inspect the EFI-MAIN NO. 1 relay.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

NG

REPLACE EFI-MAIN NO. 1 RELAY

4.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the EFI-MAIN NO. 1 relay, EFI-MAIN NO. 3 relay and EDU relay from the No. 1 engine room relay block assembly.


c.

Remove the EFI-MAIN NO. 2 relay from the No. 5 luggage room relay block assembly.

HINT:

Remove the EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2(EFI-MAIN NO.1 relay) - A106-15(MREL) Always Below 1 Ω
5(EFI-MAIN NO.1 relay) - A106-9(+B) Always Below 1 Ω
5(EFI-MAIN NO.1 relay) - A106-35(+B2) Always Below 1 Ω
2(EFI-MAIN NO.1 relay) or A106-15(MREL) - Body ground and other terminals Always 10 kΩ or higher
2(EFI-MAIN NO.1 relay), A106-15(MREL), A106-9(+B) or A106-35(+B2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)
a.
A468644C06
0.083,0.104 0.396,0.26 0.313,0.156 10 false *1 1.677,2.042 1.99,2.198 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block Assembly
*2 EFI-MAIN NO. 1 Relay


Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1(EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V
3(EFI-MAIN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 1 RELAY)

6.INSPECT IGP RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - ECM)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 D RELAY)

7.CHECK HARNESS AND CONNECTOR (IGP RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the EFI-MAIN NO. 1 relay, EFI-MAIN NO. 3 relay and EDU relay from the No. 1 engine room relay block assembly.


c.

Remove the EFI-MAIN NO. 2 relay from the No. 5 luggage room relay block assembly.

HINT:

Remove the EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5(IGP relay) - A106-2(IGP) Always Below 1 Ω
5(IGP relay) or A106-2(IGP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF IGP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF IGP RELAY)
a.

Remove the IGP relay from the No. 1 engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3(IGP relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (IGP RELAY - BODY GROUND)
a.

Remove the IGP relay from the No. 1 engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2(IGP relay) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - IG2 D RELAY)

B

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - IG2 D RELAY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - IG2 D RELAY)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-24(IGPD) - 1(IGP relay) Always Below 1 Ω
H45-24(IGPD) or 1(IGP relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - IG2 D RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-8(IG1) - 1(IGP relay) Always Below 1 Ω
H54-8(IG1) or 1(IGP relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK IGNITION OR STARTER SWITCH ASSEMBLY

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY