Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P012A11  Turbocharger/Supercharger Inlet Pressure Sensor "A" Circuit Low Circuit Short to Ground  


DESCRIPTION

The internal sensor in the E.F.I. vacuum sensor assembly detects the air inlet duct internal pressure as a voltage.

A409083E01
1.125,0.281 3.188,0.521 2.063,0.24 10 false Air inlet duct internal pressure 0.073,0.063 0.865,0.354 0.792,0.292 10 false Voltage (V) 3.052,2.385 3.406,2.677 0.354,0.292 10 false kPa 3.052,2.896 3.344,3.24 0.292,0.344 10 false psi 0.229,0.719 0.583,1.01 0.354,0.292 10 false 4.2 0.229,0.938 0.583,1.229 0.354,0.292 10 false 3.6 0.24,1.531 0.594,1.823 0.354,0.292 10 false 2.4 0.24,1.99 0.594,2.281 0.354,0.292 10 false 1.2 2.583,2.542 3.083,2.75 0.5,0.208 10 false 119.99 2.188,2.542 2.573,2.75 0.385,0.208 10 false 99.99 1.469,2.531 1.854,2.74 0.385,0.208 10 false 59.99 0.854,2.531 1.24,2.74 0.385,0.208 10 false 19.99 0.896,3.031 1.24,3.26 0.344,0.229 10 false 2.90 1.5,3.031 1.844,3.26 0.344,0.229 10 false 8.70 2.177,3.031 2.583,3.271 0.406,0.24 10 false 13.05 2.604,3.031 3.031,3.26 0.427,0.229 10 false 17.40

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P012A11 Turbocharger/Supercharger Inlet Pressure Sensor "A" Circuit Low Circuit Short to Ground The output voltage from the E.F.I. vacuum sensor assembly is below 0.6 V for 3 seconds or more (1 trip detection logic).
·

Open or short in E.F.I. vacuum sensor assembly circuit

·

E.F.I. vacuum sensor assembly

·

ECM


- SAE: P012C

HINT:

When a DTC is output, check the Data List item "Turbocharger/Supercharger Inlet Pressure Bank1" using the GTS.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Turbocharger/Supercharger Inlet Pressure Bank1 Malfunction
P012A11 Approximately 0 kPa [0 psi]
·

Short in PIC circuit to ground

·

Short in PIC circuit to EPR circuit

·

Open in VCPR circuit



If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM calculates the air inlet duct internal pressure from the E.F.I. vacuum sensor assembly output voltage. If the E.F.I. vacuum sensor assembly output voltage is not within the normal range, there may be a malfunction in the E.F.I. vacuum sensor assembly or an open or short circuit. In this case, the ECM stores a DTC.

Example:

When the sensor output voltage is below 0.6 V for 3 seconds or more, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P012A11.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A468612E03
0.417,2.438 3.479,2.635 3.063,0.198 10 false E.F.I. Vacuum Sensor Assembly 1.469,0.771 1.781,0.969 0.313,0.198 10 false VC 1.438,1.313 1.896,1.51 0.458,0.198 10 false PIC 1.5,1.854 1.813,2.052 0.313,0.198 10 false E2 4.594,0.635 5.208,0.833 0.615,0.198 10 false VCPC 4.594,1.177 5.052,1.375 0.458,0.198 10 false PIC 4.594,1.719 5.052,1.917 0.458,0.198 10 false EPIC 5.792,1.052 6.708,1.25 0.917,0.198 10 false 180 kΩ 5.802,0.385 6.26,0.583 0.458,0.198 10 false 5 V 4.302,0.635 4.615,0.833 0.313,0.198 10 false 82 4.26,1.177 4.573,1.375 0.313,0.198 10 false 105 4.323,1.719 4.781,1.917 0.458,0.198 10 false 81 1.781,0.635 1.938,0.833 0.156,0.198 10 false 3 1.781,1.188 1.938,1.385 0.156,0.198 10 false 2 1.781,1.719 1.938,1.917 0.156,0.198 10 false 1 0.417,2.25 0.875,2.448 0.458,0.198 10 false D93 5.25,2.667 5.865,2.865 0.615,0.198 10 false D104 5.25,2.854 6.865,3.667 1.615,0.813 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the E.F.I. vacuum sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D93-3(VC) - D93-1(E2) Ignition switch ON 4.5 to 5.5 V
D93-2(PIC) - D93-1(E2) Ignition switch ON 3.0 to 5.5 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D93-3(VC) - D93-2(PIC) Ignition switch off 171 to 189 kΩ



Result:
Proceed to
OK
NG



OK

REPLACE E.F.I. VACUUM SENSOR ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (E.F.I. VACUUM SENSOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (E.F.I. VACUUM SENSOR ASSEMBLY - ECM)
a.

Disconnect the E.F.I. vacuum sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D93-3(VC) - D104-82(VCPC) Always Below 1 Ω
D93-2(PIC) or D104-105(PIC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR