Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P060747  Control Module Performance Bank 1 Watchdog/Safety MCU Failure  P060787  Control Module Performance Bank 1 Missing Message  


MONITOR DESCRIPTION

The ECM continuously monitors its internal ICs and the monitor IC. If the monitor IC is abnormal, the ECM illuminates the MIL and stores DTC P060747. If an internal IC is abnormal, the ECM illuminates the MIL and stores DTC P060787.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P060747 Control Module Performance Bank 1 Watchdog/Safety MCU Failure ECM monitor IC malfunction (1 trip detection logic). ECM Comes on SAE: P0607
P060787 Control Module Performance Bank 1 Missing Message ECM internal IC malfunction (1 trip detection logic). ECM Comes on SAE: P0607

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the GTS off.

6.

Turn the ignition switch off.

7.

Disconnect the GTS.

8.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

9.

Connect the cable to the negative (-) battery terminal.

10.

Connect the GTS to the DLC3.

11.

Turn the ignition switch to ON.

12.

Turn the GTS on.

13.

Wait 1 second or more.

14.

Enter the following menus: Powertrain / Engine / Trouble Codes.

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P060747 or P060787

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.




HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P060747 OR P060787)
2.READ OUTPUT DTC (DTC P060747 OR P060787)
a.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


b.

Connect the cable to the negative (-) battery terminal.


c.

Wait 1 second or more.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P060747 or P060787 is output B




A

B