Home › Drivetrain › CLUTCH › CLUTCH UNIT (for EA67F) › from 2020.09
RM36W0E _52 Drivetrain _089426 CLUTCH _0447224 CLUTCH UNIT(for EA67F) A

CLUTCH  CLUTCH UNIT(for EA67F)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 31001 1.INSTALL COVER AND DISC CLUTCH SET

a.
C450667C01
2.531,1.5 2.781,1.5 false 2.188,3.667 2.188,3.917 false 1.802,2.917 2.135,2.917 false 1.167,2.708 1.5,2.708 true 2.229,2.833 2.542,2.99 0.313,0.156 10 false *1 0.969,2.604 1.281,2.76 0.313,0.156 10 false *2 1.167,3.448 1.479,3.604 0.313,0.156 10 false *a 2.865,1.427 3.323,1.625 0.458,0.198 10 false SST 2.063,3.969 2.521,4.167 0.458,0.198 10 false SST
*1 Clutch Disc Assembly
*2 Flywheel Sub-assembly
*a Flywheel Sub-assembly Side


Insert SST into the clutch disc assembly, then insert them both into the flywheel sub-assembly.

SST
09301-00230  

NOTICE:
·

Keep the lined part of the clutch disc assembly, the pressure plate, and the surface of the flywheel sub-assembly away from oil and foreign matter.

·

Insert the clutch disc assembly in the correct direction.




b.
C450668C01
0.979,0.875 0.417,1.177 0.417,1.177 1.052,0.896 true 2.021,1.094 2.604,0.51 2.604,0.51 2.771,0.51 true 0.24,1.125 0.552,1.281 0.313,0.156 10 false *a 0.542,1.302 0.698,1.49 0.156,0.188 10 false 3 1.083,1.99 1.24,2.177 0.156,0.188 10 false 6 2.51,1.979 2.667,2.167 0.156,0.188 10 false 2 2.844,0.427 3.344,0.583 0.5,0.156 10 false SST 2.906,0.833 3.063,1.021 0.156,0.188 10 false 5 2.344,0.031 3,0.219 0.656,0.188 10 false 1 (*b), 4 0.875,0.208 1.031,0.396 0.156,0.188 10 false 7
*a Match mark
*b Temporarily Tighten


Align the match mark on the clutch cover assembly with the one on the flywheel sub-assembly.


c.

Following the procedure shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

SST
09301-00230  

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.




Hide 31210 2.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C450669

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

Maximum Non-alignment:

0.5 mm (0.0197 in.)



b.
C450670N01
2.125,1.344 2.531,0.865 true 2.583,0.771 3.042,0.969 0.458,0.198 10 false SST

If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31400 3.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

a.
C450671

Temporarily tighten the clutch release cylinder to bleeder tube to a new clutch release cylinder with bearing assembly.

NOTICE:

Do not allow any foreign matter such as dirt or dust to enter the clutch release cylinder to bleeder tube from the connecting part.



b.

Clean and degrease all installation surfaces for the clutch release cylinder with bearing assembly.


c.
C450672

Install the clutch release cylinder with bearing assembly with 3 new bolts.

Torque:
22.5 N*m (229 kgf*cm, 17 ft.*lbf)

NOTICE:
·

The clutch release cylinder with bearing assembly and installation bolts cannot be reused and must be replaced with new ones.

·

Clean and degrease all installation surfaces and make sure that the clutch release cylinder with bearing assembly fits securely with the manual transaxle assembly during installation. The first bolt should be tightened by hand while holding the clutch release cylinder with bearing assembly.

·

Ensure that none of the clutch spline grease adheres to the clutch release cylinder with bearing assembly.

·

The clutch release cylinder with bearing assembly cannot be disassembled.




d.

Install the clutch tube boot onto the manual transaxle assembly.


e.
C450673

Temporarily tighten the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.


f.
C450674C01
2.365,0.396 2.583,0.615 true 2.104,0.281 2.323,0.458 0.219,0.177 10 true *a
*a Rotation Prevention Tab


Temporarily tighten the bolt and install the clutch release bleeder sub-assembly.

NOTICE:

Install the parts so that the rotation prevention tab of the clutch release bleeder sub-assembly is contacting the rib of the manual transaxle assembly.



g.
C450675C01
2.948,0.625 3.208,0.854 0.26,0.229 10 true *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the clutch release cylinder to bleeder tube to the clutch release cylinder with bearing assembly.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the clutch release cylinder to bleeder tube.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




h.
C450676C01
0,0 0,0 false
V100135

Clutch Spline Grease


Apply clutch spline grease to the input shaft splines.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 31224 4.INSTALL CLUTCH RELEASE BEARING PLATE

a.
C450677

Install a new clutch release bearing plate to the clutch release cylinder with bearing assembly.

NOTICE:

After installing the clutch release bearing plate to the clutch release cylinder with bearing assembly, check that there are no gaps.



Hide 31407B 5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 6.INSPECT CLUTCH PIPE LINE

a.
C450678

Using SST, apply pressure of 100 kPa (1.0 kgf/cm2, 15 psi) to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.

SST
09992-00242  

If the pressure drops, replace the clutch release cylinder to bleeder tube.


Hide 31407B 7.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C450674C01
2.365,0.396 2.583,0.615 true 2.104,0.281 2.323,0.458 0.219,0.177 10 true *a
*a Rotation Prevention Tab


Temporarily tighten the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.

NOTICE:

Install the parts so that the rotation prevention tab of the clutch release bleeder sub-assembly is contacting the rib of the manual transaxle assembly.



b.

Install the bolt and clutch release bleeder sub-assembly.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
C450679C01
1.604,3.208 1.917,3.365 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the clutch release cylinder to bleeder tube.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the clutch release cylinder to bleeder tube.

·

Do not allow any foreign matter such as dirt or dust to enter the clutch release cylinder to bleeder tube from the connecting part.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 31483 8.INSTALL BLEEDER CLUTCH RELEASE TUBE

a.

Install the clamp to the bleeder clutch release tube.


b.

Temporarily tighten the bleeder clutch release tube to the clutch release bleeder sub-assembly.


c.
C450680C01
1.396,2.979 1.708,3.135 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Install the bleeder clutch release tube to the manual transaxle assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Using a 10 mm union nut wrench, install the bleeder clutch release tube to the clutch release bleeder sub-assembly.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the bleeder clutch release tube.

·

Do not allow any foreign matter such as dirt or dust to enter the bleeder clutch release tube from the connecting part.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)