Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front) › from 2020.09
RM36W0E _56 Audio / Visual / Telematics _088657 PARK ASSIST / MONITORING _0422050 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  INSTALLATION  


PROCEDURE

Hide 89347B 1.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (for 5 Door)

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

If a front corner ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the front bumper cover.

i.

Remove any remaining double-sided tape from the front bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 30 mm (1.18 in.)


Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.


c.
E436540C02
1.021,0.667 0.656,0.333 true 0.396,0.24 0.625,0.438 0.229,0.198 10 true *a
*a Scribed Line
V100144

Primer Application


Apply primer to front bumper assembly on the installation area of the front corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front corner ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new front corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.
E436541C01
0.448,0.635 0.781,0.802 true 2.365,0.854 2.875,0.438 2.875,0.438 2.375,0.521 true 0.188,0.5 0.417,0.698 0.229,0.198 10 true *a 2.927,0.344 3.156,0.542 0.229,0.198 10 true *b
*a Scribed Line
*b Identification Code


Check that the identification codes on the front bumper assembly and the front corner ultrasonic sensor retainer are identical.


h.

Align the front corner ultrasonic sensor retainer with the scribed line on the front bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the front corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the rear bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89347B 2.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (for 3 Door)

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

If a front corner ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the front bumper cover.

i.

Remove any remaining double-sided tape from the front bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 32 mm (1.26 in.)


Cover the 2 sensor installation holes with a 32 mm (1.26 in.) circular piece of tape.


c.
E450588C01
2.5,1.927 2.177,1.729 true 2.531,1.906 2.76,2.104 0.229,0.198 10 true *a
*a Scribed Line
V100144

Primer Application


Apply primer to front bumper assembly on the installation area of the front corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front corner ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new front corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.
E450589C01
2.156,1.729 2.531,1.875 true 2.844,0.802 3,0.333 3,0.333 2.365,0.802 true 2.563,1.844 2.75,2.031 0.188,0.188 10 true *a 2.938,0.135 3.125,0.313 0.188,0.177 10 true *b
*a Scribed Line
*b Identification Code


Check that the identification codes on the front bumper assembly and the front corner ultrasonic sensor retainer are identical.


h.

Align the front corner ultrasonic sensor retainer with the scribed line on the front bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the front corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the rear bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89341L 3.INSTALL FRONT CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.

for 5 Door:

i.
E436543C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front center ultrasonic sensor as shown in the illustration.


ii.

Connect the connector.



b.

for 3 Door:

i.
E450586C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front center ultrasonic sensor as shown in the illustration.


ii.

Connect the connector.



Hide 89341K 4.INSTALL FRONT CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.

for 5 Door:

i.
E436542C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front corner ultrasonic sensor as shown in the illustration.


ii.

Connect the connector.



b.

for 3 Door:

i.
E450587C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front corner ultrasonic sensor as shown in the illustration.


ii.

Connect the connector.



Hide 89348N 5.INSTALL NO. 1 ULTRASONIC SENSOR CLIP

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E436552C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the No. 1 ultrasonic sensor clip as shown in the illustration.


b.

Engage the wire harness clamp.