Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › from 2020.09
RM36W0E _56 Audio / Visual / Telematics _088657 PARK ASSIST / MONITORING _0422051 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Ultrasonic sensor (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system

·

Parking support brake system


(Click here)

PROCEDURE

Hide 89348N 2.REMOVE NO. 1 ULTRASONIC SENSOR CLIP (for 3 Door)

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E450591

Disengage the wire harness clamp.


b.
E450592C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the No. 1 ultrasonic sensor clip as shown in the illustration.


Hide 89342 3.REMOVE REAR CORNER ULTRASONIC SENSOR (for 5 Door)

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E436515C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


b.

Disengage the claws to remove the rear corner ultrasonic sensor.


Hide 89342 4.REMOVE REAR CORNER ULTRASONIC SENSOR (for 3 Door)

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E450594C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


b.

Disengage the claws to remove the rear corner ultrasonic sensor.


Hide 89342A 5.REMOVE REAR CENTER ULTRASONIC SENSOR (for 5 Door)

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E436514C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


b.

Disengage the claws to remove the rear center ultrasonic sensor.


Hide 89342A 6.REMOVE REAR CENTER ULTRASONIC SENSOR (for 3 Door)

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E450593C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


b.

Disengage the claws to remove the rear center ultrasonic sensor.


Hide 89348R 7.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (for 5 Door)

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E436516

Remove the rear corner ultrasonic sensor retainer.


Hide 89348R 8.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (for 3 Door)

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E450595

Remove the rear corner ultrasonic sensor retainer.


Hide 89348S 9.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER (for 5 Door)

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Center Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E436516

Remove the rear center ultrasonic sensor retainer.


Hide 89348S 10.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER (for 3 Door)

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Center Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E450595

Remove the rear center ultrasonic sensor retainer.