Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for RHD) › from 2020.09
RM36W0E _52 Drivetrain _089426 CLUTCH _0430792 CLUTCH PEDAL(for RHD) A

CLUTCH  CLUTCH PEDAL(for RHD)  INSTALLATION  


PROCEDURE

Hide 31321 1.INSTALL CLUTCH PEDAL PAD

a.

Install the clutch pedal pad to the clutch pedal sub-assembly.


Hide 31453B 2.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSHING

a.

Install a new clutch master cylinder push rod clevis bushing to the clutch pedal sub-assembly.

NOTICE:

Install the clutch master cylinder push rod clevis bushing from the left side of the vehicle.



b.

for G16-GTS:

i.
C450367C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the inside of the clutch master cylinder push rod clevis bushing.



c.

except G16-GTS:

i.
C434805C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the inside of the clutch master cylinder push rod clevis bushing.



Hide 31324A 3.INSTALL CLUTCH PEDAL SHAFT COLLAR

a.

Install the clutch pedal shaft collar to the clutch pedal sub-assembly.


b.
C431230C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to both sides of 2 new clutch pedal bushings.


c.

Install the 2 clutch pedal bushings to the clutch pedal sub-assembly.


Hide 31301P 4.INSTALL CLUTCH PEDAL TURNOVER BUSH (except 1KR-FE)

a.
C431231C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the inside of the clutch pedal turnover bushing.


b.

Install the clutch pedal turnover bushing to the clutch pedal sub-assembly.


Hide 31353 5.INSTALL CLUTCH PEDAL SPRING HOLDER (except 1KR-FE)

a.
C431232C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the contact surface of the clutch pedal spring holder.


b.

Install the clutch pedal spring holder to the clutch pedal support sub-assembly.


Hide 31301 6.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)

NOTICE:
·

Install the bolt from the right side of the vehicle.

·

Turn the nut while holding the bolt.




Hide 31301A 7.INSTALL CLUTCH PEDAL SPRING (except 1KR-FE)

a.

Move the clutch pedal sub-assembly to the full stroke position.


b.

Install the clutch pedal spring to the clutch pedal sub-assembly and clutch pedal bracket sub-assembly.


Hide 89280 8.INSTALL CLUTCH PEDAL STROKE SENSOR ASSEMBLY (for G16E-GTS)

Hide 88280A 9.INSTALL CLUTCH SWITCH ASSEMBLY (except G16E-GTS)

Hide 10.INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY

a.

for G16-GTS:

i.

Install the clutch pedal support assembly to the vehicle body with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


ii.

Engage the clamp to connect the wire harness to the clutch pedal support assembly.


iii.

Connect the clutch pedal stroke sensor assembly connector.



b.

except G16-GTS:

i.

Install the clutch pedal support assembly to the vehicle body with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


ii.

Engage the 2 clamps to connect the wire harness to the clutch pedal support assembly.


iii.

Connect the clutch switch assembly connector.



Hide 31453A 11.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

a.
C431233C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the clevis pin.


b.

Connect the clutch master cylinder assembly to the clutch pedal sub-assembly with the master cylinder push rod clevis with hole pin.

NOTICE:

Install the clevis pin from the left side of the vehicle.



c.

Install a new clip to the master cylinder push rod clevis with hole pin.


Hide 31301F 12.INSTALL CLUTCH PEDAL STOPPER BOLT (for G16E-GTS)

a.
C446041C02
2,1.25 2.25,0.75 2.25,0.75 2.417,0.75 true 2.021,1.469 2.854,1.469 true 2.448,0.677 2.76,0.833 0.313,0.156 10 false *1 2.885,1.396 3.198,1.552 0.313,0.156 10 false *2
*1 Clutch Pedal Stopper Bolt
*2 Clutch Pedal Stopper Nut


Temporarily install the clutch pedal stopper bolt and clutch pedal stopper nut to the clutch pedal support sub-assembly.


b.
C446043C02
2.458,1.146 2.615,1.344 0.156,0.198 10 false *a
*a Clearance


Without depressing the clutch pedal, check that the clearance shown in the illustration is as specified.

Standard clearance:

1.8 to 2.8 mm (0.0709 to 0.1102 in.)



c.

Fix the clutch pedal stopper bolt and tighten the clutch pedal stopper nut.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 84520 13.INSTALL CLUTCH START SWITCH ASSEMBLY

Hide 14.INSTALL STEERING COLUMN ASSEMBLY

Hide 88280A 16.INSPECT CLUTCH START SYSTEM