Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (for Gasoline Model without Entry and Start System) › from 2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424970 IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System)  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  B279999  Engine Immobiliser System Exceeded Learning Limit  


DESCRIPTION

The ECM stores this DTC when a communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Wire harness or connector

·

Transponder key ECU assembly

·

ECM


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.

·

After disconnecting and reconnecting the cable to the negative (-) auxiliary battery terminal, turn the ignition switch to ON and wait 10 seconds.


B279999 Engine Immobiliser System Exceeded Learning Limit One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Wire harness or connector

·

Transponder key ECU assembly

·

ECM


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.

·

After disconnecting and reconnecting the cable to the negative (-) auxiliary battery terminal, turn the ignition switch to ON and wait 10 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B279986 -
B279999

WIRING DIAGRAM

for M15A-FKS:
E366879E30
1.615,0.99 2.073,1.188 0.458,0.198 10 false IMO 1.656,1.802 2.115,2 0.458,0.198 10 false IMI 1.99,0.99 3,1.219 1.01,0.229 10 false 47 1.969,1.813 2.833,2.104 0.865,0.292 10 false 61 5.042,1.021 5.5,1.219 0.458,0.198 10 false 10 5.042,1.823 5.5,2.021 0.458,0.198 10 false 11 5.302,1.021 5.76,1.219 0.458,0.198 10 false EFII 4.958,2.802 5.417,3 0.458,0.198 10 false H74 5.302,1.823 5.76,2.021 0.458,0.198 10 false EFIO 1.115,2.844 2.104,3.042 0.99,0.198 10 false A54 1.104,3.021 1.875,3.323 0.771,0.302 10 false ECM 4.938,2.958 6.969,3.479 2.031,0.521 10 false Transponder Key ECU Assembly 1.344,1.375 1.802,1.573 0.458,0.198 10 false 12 V 6.01,0.542 6.469,0.74 0.458,0.198 10 false 12 V

for 1KR-FE:
E366879E31
1.615,0.99 2.073,1.188 0.458,0.198 10 false IMO 1.656,1.802 2.115,2 0.458,0.198 10 false IMI 1.99,0.99 3,1.219 1.01,0.229 10 false 43 1.969,1.813 2.833,2.104 0.865,0.292 10 false 42 5.042,1.021 5.5,1.219 0.458,0.198 10 false 10 5.042,1.823 5.5,2.021 0.458,0.198 10 false 11 5.302,1.021 5.76,1.219 0.458,0.198 10 false EFII 4.958,2.802 5.417,3 0.458,0.198 10 false H74 5.302,1.823 5.76,2.021 0.458,0.198 10 false EFIO 1.115,2.844 2.104,3.042 0.99,0.198 10 false A55 1.104,3.021 1.875,3.323 0.771,0.302 10 false ECM 4.938,2.958 6.969,3.479 2.031,0.521 10 false Transponder Key ECU Assembly 1.344,1.375 1.802,1.573 0.458,0.198 10 false 12 V 6.01,0.542 6.469,0.74 0.458,0.198 10 false 12 V

for G16E-GTS:
E366879E39
1.615,0.99 2.073,1.188 0.458,0.198 10 false IMO 1.656,1.802 2.115,2 0.458,0.198 10 false IMI 1.99,0.99 3,1.219 1.01,0.229 10 false 47 1.969,1.813 2.833,2.104 0.865,0.292 10 false 61 5.042,1.021 5.5,1.219 0.458,0.198 10 false 10 5.042,1.823 5.5,2.021 0.458,0.198 10 false 11 5.302,1.021 5.76,1.219 0.458,0.198 10 false EFII 4.958,2.802 5.417,3 0.458,0.198 10 false H74 5.302,1.823 5.76,2.021 0.458,0.198 10 false EFIO 1.063,2.844 2.052,3.042 0.99,0.198 10 false A106 1.073,3.01 1.844,3.313 0.771,0.302 10 false ECM 4.938,2.958 6.969,3.479 2.031,0.521 10 false Transponder Key ECU Assembly 1.344,1.375 1.802,1.573 0.458,0.198 10 false 12 V 6.01,0.542 6.469,0.74 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for M15A-FKS A
for 1KR-FE B
for G16E-GTS C



A

2.REGISTER ECU COMMUNICATION ID

B

9.REGISTER ECU COMMUNICATION ID

C

16.REGISTER ECU COMMUNICATION ID
2.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.


Result:
Proceed to
NEXT



NEXT

3.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)
3.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.

B463094C14
3.417,0.333 3.833,0.604 0.417,0.271 3.073,2.323 3.365,1.573 true 2.74,4.552 2.875,4.094 true 3.177,4.531 3.063,4.094 true 0.927,4.063 1.385,4.26 0.458,0.198 10 false GND 0.365,0.188 0.792,0.5 0.427,0.313 10 false *a 2.906,3.125 3.333,3.438 0.427,0.313 10 false *b 3.49,0.375 3.927,0.646 0.438,0.271 10 false H74 2.76,2.302 3.219,2.5 0.458,0.198 10 false EFII 2.563,4.542 2.875,4.76 0.313,0.219 10 false *c 3.198,4.552 3.51,4.771 0.313,0.219 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.



Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-10 (EFII) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

OK:

Waveform is similar to that shown in the illustration.


Result:
Result Proceed to
OK A
NG (Terminal EFII stuck low (2.4 V or less)) B
NG (Terminal EFII stuck high (12 V) or abnormal waveform) C



A

4.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

B

7.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

4.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B463095C20
3.396,0.385 3.781,0.656 0.385,0.271 2.99,2.198 3.229,1.552 true 3.24,4.563 3.292,4.083 true 3.521,4.563 3.479,4.083 true 0.375,0.125 0.688,0.323 0.313,0.198 10 false *a 3.458,0.427 3.771,0.625 0.313,0.198 10 false H74 2.646,2.219 3.104,2.448 0.458,0.229 10 false EFIO 3.333,3.021 3.792,3.25 0.458,0.229 10 false *b 0.958,4.042 1.417,4.271 0.458,0.229 10 false GND 3.052,4.531 3.313,4.719 0.26,0.188 10 false *c 3.552,4.552 3.813,4.74 0.26,0.188 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-11 (EFIO) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

5.REGISTER ECU COMMUNICATION ID

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

7.INSPECT ECM (IMO TERMINAL VOLTAGE)

Pre-procedure1

a.

Disconnect the A54 ECM connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result
A54-47 (IMO) - Body ground Ignition switch turned to ON using registered door control transmitter assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Post-procedure1

c.

None


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

B

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the H74 transponder key ECU assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-10 (EFII) - A54-47 (IMO) Always Below 1 Ω
H74-10 (EFII) or A54-47 (IMO) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.


Result:
Proceed to
NEXT



NEXT

10.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)
10.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.

B463094C14
3.417,0.333 3.833,0.604 0.417,0.271 3.073,2.323 3.365,1.573 true 2.74,4.552 2.875,4.094 true 3.177,4.531 3.063,4.094 true 0.927,4.063 1.385,4.26 0.458,0.198 10 false GND 0.365,0.188 0.792,0.5 0.427,0.313 10 false *a 2.906,3.125 3.333,3.438 0.427,0.313 10 false *b 3.49,0.375 3.927,0.646 0.438,0.271 10 false H74 2.76,2.302 3.219,2.5 0.458,0.198 10 false EFII 2.563,4.542 2.875,4.76 0.313,0.219 10 false *c 3.198,4.552 3.51,4.771 0.313,0.219 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.



Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-10 (EFII) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

OK:

Waveform is similar to that shown in the illustration.


Result:
Result Proceed to
OK A
NG (Terminal EFII stuck low (2.4 V or less)) B
NG (Terminal EFII stuck high (12 V) or abnormal waveform) C



A

11.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

B

14.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

11.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B463095C20
3.396,0.385 3.781,0.656 0.385,0.271 2.99,2.198 3.229,1.552 true 3.24,4.563 3.292,4.083 true 3.521,4.563 3.479,4.083 true 0.375,0.125 0.688,0.323 0.313,0.198 10 false *a 3.458,0.427 3.771,0.625 0.313,0.198 10 false H74 2.646,2.219 3.104,2.448 0.458,0.229 10 false EFIO 3.333,3.021 3.792,3.25 0.458,0.229 10 false *b 0.958,4.042 1.417,4.271 0.458,0.229 10 false GND 3.052,4.531 3.313,4.719 0.26,0.188 10 false *c 3.552,4.552 3.813,4.74 0.26,0.188 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-11 (EFIO) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

12.REGISTER ECU COMMUNICATION ID

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

12.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER ENGINE STARTS
13.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

14.INSPECT ECM (IMO TERMINAL VOLTAGE)

Pre-procedure1

a.

Disconnect the A55 ECM connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result
A55-43 (IMO) - Body ground Ignition switch turned to ON using registered door control transmitter assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Post-procedure1

c.

None


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

15.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

B

15.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the H74 transponder key ECU assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-10 (EFII) - A55-43 (IMO) Always Below 1 Ω
H74-10 (EFII) or A55-43 (IMO) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.


Result:
Proceed to
NEXT



NEXT

17.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)
17.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.

B463094C14
3.417,0.333 3.833,0.604 0.417,0.271 3.073,2.323 3.365,1.573 true 2.74,4.552 2.875,4.094 true 3.177,4.531 3.063,4.094 true 0.927,4.063 1.385,4.26 0.458,0.198 10 false GND 0.365,0.188 0.792,0.5 0.427,0.313 10 false *a 2.906,3.125 3.333,3.438 0.427,0.313 10 false *b 3.49,0.375 3.927,0.646 0.438,0.271 10 false H74 2.76,2.302 3.219,2.5 0.458,0.198 10 false EFII 2.563,4.542 2.875,4.76 0.313,0.219 10 false *c 3.198,4.552 3.51,4.771 0.313,0.219 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.



Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-10 (EFII) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

OK:

Waveform is similar to that shown in the illustration.


Result:
Result Proceed to
OK A
NG (Terminal EFII stuck low (2.4 V or less)) B
NG (Terminal EFII stuck high (12 V) or abnormal waveform) C



A

18.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

B

21.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

18.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B463095C20
3.396,0.385 3.781,0.656 0.385,0.271 2.99,2.198 3.229,1.552 true 3.24,4.563 3.292,4.083 true 3.521,4.563 3.479,4.083 true 0.375,0.125 0.688,0.323 0.313,0.198 10 false *a 3.458,0.427 3.771,0.625 0.313,0.198 10 false H74 2.646,2.219 3.104,2.448 0.458,0.229 10 false EFIO 3.333,3.021 3.792,3.25 0.458,0.229 10 false *b 0.958,4.042 1.417,4.271 0.458,0.229 10 false GND 3.052,4.531 3.313,4.719 0.26,0.188 10 false *c 3.552,4.552 3.813,4.74 0.26,0.188 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-11 (EFIO) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

19.REGISTER ECU COMMUNICATION ID

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

19.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.


Result:
Proceed to
NEXT



NEXT

20.CHECK WHETHER ENGINE STARTS
20.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

21.INSPECT ECM (IMO TERMINAL VOLTAGE)

Pre-procedure1

a.

Disconnect the A106 ECM connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result
A106-47 (IMO) - Body ground Ignition switch turned to ON using registered door control transmitter assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Post-procedure1

c.

None


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

22.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

B

22.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the H74 transponder key ECU assembly connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-10 (EFII) - A106-47 (IMO) Always Below 1 Ω
H74-10 (EFII) or A106-47 (IMO) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR