Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › from 2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  B279999  Engine Immobiliser System Exceeded Learning Limit  


DESCRIPTION

w/ Wireless Door Lock Buzzer Answer-back Function:

If there is a communication malfunction between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.


w/o Wireless Door Lock Buzzer Answer-back Function:

If there is a communication malfunction between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either of the following conditions is met (1 trip detection logic*):
w/ Wireless Door Lock Buzzer Answer-back Function:
·

A malfunction is detected in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly).

·

The communication ID codes of the ECM and certification ECU (smart key ECU assembly) do not match.


w/o Wireless Door Lock Buzzer Answer-back Function:
·

A malfunction is detected in the communication or communication lines between the ECM and ID code box (immobiliser code ECU).

·

The communication ID codes of the ECM and ID code box (immobiliser code ECU) do not match.


w/ Wireless Door Lock Buzzer Answer-back Function:
·

Certification ECU (smart key ECU assembly)

·

ECM

·

Harness or connector


w/o Wireless Door Lock Buzzer Answer-back Function:
·

ID code box (immobiliser code ECU)

·

ECM

·

Harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the engine and wait for 10 seconds. If there is a malfunction, the engine will stop (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) auxiliary battery terminal, start the engine and wait for 10 seconds (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).


B279999 Engine Immobiliser System Exceeded Learning Limit Either of the following conditions is met (1 trip detection logic*):
·

A malfunction is detected in the communication or communication lines between the ECM and ID code box (immobiliser code ECU).

·

The communication ID codes of the ECM and ID code box (immobiliser code ECU) do not match.


·

ID code box (immobiliser code ECU)

·

ECM

·

Harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the engine and wait for 10 seconds. If there is a malfunction, the engine will stop (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) auxiliary battery terminal, start the engine and wait for 10 seconds (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B279986 -
B279999

WIRING DIAGRAM

w/ Wireless Door Lock Buzzer Answer-back Function


B463090E76
0.698,3.073 2.677,3.427 1.979,0.354 10 false ECM 0.708,2.906 2.167,3.208 1.458,0.302 10 false A54*1, A106*2 5.333,2.906 5.792,3.104 0.458,0.198 10 false H45 6.042,0.24 6.5,0.438 0.458,0.198 10 false +B 1.188,1.375 1.646,1.573 0.458,0.198 10 false +B 5.292,0.969 5.75,1.167 0.458,0.198 10 false EFII 5.302,1.865 5.76,2.063 0.458,0.198 10 false EFIO 5.104,0.969 5.563,1.167 0.458,0.198 10 false 4 5.104,1.865 5.563,2.063 0.458,0.198 10 false 5 1.625,0.948 2.208,1.167 0.583,0.219 10 false IMO 1.688,1.865 2.146,2.063 0.458,0.198 10 false IMI 1.969,0.948 2.958,1.26 0.99,0.313 10 false 47 1.99,1.865 3.313,2.125 1.323,0.26 10 false 61 5.333,3.063 6.969,3.427 1.635,0.365 10 false Certification ECU (Smart Key ECU Assembly) 2.25,3.021 4.698,3.219 2.448,0.198 10 false *1: for M15A-FKS 2.25,3.333 4.698,3.531 2.448,0.198 10 false *2: for G16E-GTS


w/o Wireless Door Lock Buzzer Answer-back Function


B463090E77
0.375,3.073 2.354,3.427 1.979,0.354 10 false ECM 0.385,2.906 1.906,3.219 1.521,0.313 10 false A54*1, A55*2, A106*3 5.333,2.906 5.792,3.104 0.458,0.198 10 false H67 6.042,0.24 6.5,0.438 0.458,0.198 10 false +B 1.188,1.375 1.646,1.573 0.458,0.198 10 false +B 5.292,0.969 5.75,1.167 0.458,0.198 10 false EFII 5.302,1.865 5.76,2.063 0.458,0.198 10 false EFIO 5.104,0.969 5.563,1.167 0.458,0.198 10 false 3 5.104,1.865 5.563,2.063 0.458,0.198 10 false 4 1.625,0.948 2.208,1.167 0.583,0.219 10 false IMO 1.688,1.865 2.146,2.063 0.458,0.198 10 false IMI 1.969,0.948 3.021,1.24 1.052,0.292 10 false 47*1, *3, 43*2 1.99,1.854 3.313,2.115 1.323,0.26 10 false 61*1, *3, 42*2 5.333,3.063 6.896,3.406 1.563,0.344 10 false ID Code Box (Immobiliser Code ECU) 2.5,2.75 4.948,2.948 2.448,0.198 10 false *1: for M15A-FKS 2.5,3.083 4.948,3.281 2.448,0.198 10 false *2: for 1KR-FE 2.5,3.417 4.948,3.615 2.448,0.198 10 false *3: for G16E-GTS


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ECM, certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

*1: w/ Wireless Door Lock Buzzer Answer-back Function

*2: w/o Wireless Door Lock Buzzer Answer-back Function




HINT:

When DTC B279986*1 or B279999*2 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

*1: except 1KR-FE

*2: for 1KR-FE



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Wireless Door Lock Buzzer Answer-back Function A
w/o Wireless Door Lock Buzzer Answer-back Function B



A

2.REGISTER ECU COMMUNICATION ID

B

13.REGISTER ECU COMMUNICATION ID
2.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFII)
3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.

B574559C02
2.052,0.042 2.469,0.292 0.417,0.25 3.198,3.552 3.031,3.552 3.031,3.552 3.031,3.042 true 2.667,3.563 2.833,3.563 2.833,3.563 2.833,3.052 true 2.823,1.5 2.656,1.5 2.656,1.5 1.938,0.635 true 0.219,0.104 0.531,0.26 0.313,0.156 10 false *a 2.854,2.115 3.167,2.271 0.313,0.156 10 false *b 2.479,3.49 2.792,3.646 0.313,0.156 10 false *c 3.25,3.479 3.563,3.635 0.313,0.156 10 false *d 0.885,3 1.198,3.156 0.313,0.156 10 false GND 2.885,1.417 3.198,1.573 0.313,0.156 10 false EFII 2.125,0.094 2.438,0.25 0.313,0.156 10 false H45
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
H45-4 (EFII) - Body ground Within 3 seconds of the engine start operation being performed or within 3 seconds of the ignition switch being turned to ON after connecting the cable to the negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal EFII stuck low (2.4 V or less)*1 B
Terminal EFII stuck low (2.4 V or less)*2 C
Waveform not output, or has abnormal wavelength or shape, or terminal EFII stuck high (12 V)*1 D
Waveform not output, or has abnormal wavelength or shape, or terminal EFII stuck high (12 V)*2 E


*1: for M15A-FKS

*2: for G16E-GTS



A

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)

B

7.CHECK ECM

C

9.CHECK ECM

D

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

E

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B574558C02
2.167,0.042 2.594,0.292 0.427,0.25 1.719,1.531 1.906,1.531 1.906,1.531 1.938,0.625 true 3.583,3.531 3.417,3.531 3.417,3.531 3.417,3.031 true 3.073,3.542 3.24,3.542 3.24,3.542 3.24,3.042 true 0.219,0.125 0.531,0.281 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.844,2.99 1.323,3.198 0.479,0.208 10 false GND 2.26,0.094 2.573,0.25 0.313,0.156 10 false H45 1.344,1.448 1.865,1.656 0.521,0.208 10 false EFIO
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
H45-5 (EFIO) - Body ground Within 3 seconds of the engine start operation being performed or within 3 seconds of the ignition switch being turned to ON after connecting the cable to the negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

5.REGISTER ECU COMMUNICATION ID (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.REGISTER ECU COMMUNICATION ID (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the ignition switch to ON.


b.

Check that the engine can be started 5 seconds after the ignition switch turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for M15A-FKS) B
NG (for G16E-GTS) C



A

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

B

C

7.CHECK ECM

Pre-procedure1

a.

Disconnect the A54 ECM connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-47 (IMO) - Body ground Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Post-procedure1

c.

None


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

B

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

Pre-procedure1

a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-47 (IMO) - H45-4 (EFII) Always Below 1 Ω
A54-47 (IMO) or H45-4 (EFII) - Other terminals and body ground Always 10 kΩ or higher
A54-61 (IMI) - H45-5 (EFIO) Always Below 1 Ω
A54-61 (IMI) or H45-5 (EFIO) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK ECM

Pre-procedure1

a.

Disconnect the A106 ECM connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A106-47 (IMO) - Body ground Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Post-procedure1

c.

None


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

B

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

Pre-procedure1

a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A106-47 (IMO) - H45-4 (EFII) Always Below 1 Ω
A106-47 (IMO) or H45-4 (EFII) - Other terminals and body ground Always 10 kΩ or higher
A106-61 (IMI) - H45-5 (EFIO) Always Below 1 Ω
A106-61 (IMI) or H45-5 (EFIO) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

Pre-procedure1

a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A54 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-47 (IMO) - H45-4 (EFII) Always Below 1 Ω
A54-47 (IMO) or H45-4 (EFII) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

Pre-procedure1

a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A106 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A106-47 (IMO) - H45-4 (EFII) Always Below 1 Ω
A106-47 (IMO) or H45-4 (EFII) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFII)
14.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.

E446704C03
3.25,0.052 3.667,0.302 0.417,0.25 3.198,3.552 3.031,3.552 3.031,3.552 3.031,3.042 true 2.667,3.563 2.833,3.563 2.833,3.563 2.833,3.052 true 4.333,1.583 4.167,1.583 4.167,1.583 3.563,0.906 true 0.219,0.104 0.531,0.26 0.313,0.156 10 false *a 2.854,2.115 3.167,2.271 0.313,0.156 10 false *b 2.479,3.49 2.792,3.646 0.313,0.156 10 false *c 3.25,3.479 3.563,3.635 0.313,0.156 10 false *d 0.885,3 1.198,3.156 0.313,0.156 10 false GND 4.417,1.51 4.729,1.667 0.313,0.156 10 false EFII 3.333,0.094 3.708,0.25 0.375,0.156 10 false H67
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
H67-3 (EFII) - Body ground Within 3 seconds of the engine start operation being performed or within 3 seconds of the ignition switch being turned to ON after connecting the cable to the negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal EFII stuck low (2.4 V or less)*1 B
Terminal EFII stuck low (2.4 V or less)*2 C
Terminal EFII stuck low (2.4 V or less)*3 D
Waveform not output, or has abnormal wavelength or shape, or terminal EFII stuck high (12 V)*1 E
Waveform not output, or has abnormal wavelength or shape, or terminal EFII stuck high (12 V)*2 F
Waveform not output, or has abnormal wavelength or shape, or terminal EFII stuck high (12 V)*3 G


*1: for M15A-FKS

*2: for G16E-GTS

*3: for 1KR-FE



A

15.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)

B

18.CHECK ECM

C

20.CHECK ECM

D

22.CHECK ECM

E

24.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

F

25.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

G

26.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
15.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

E446705C02
3.292,0.094 3.719,0.344 0.427,0.25 2.896,1.573 3.083,1.573 3.083,1.573 3.365,0.917 true 3.583,3.531 3.417,3.531 3.417,3.531 3.417,3.031 true 3.073,3.542 3.24,3.542 3.24,3.542 3.24,3.042 true 0.219,0.125 0.531,0.281 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.844,2.99 1.323,3.198 0.479,0.208 10 false GND 3.375,0.146 3.688,0.302 0.313,0.156 10 false H67 2.521,1.5 3.042,1.708 0.521,0.208 10 false EFIO
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
H67-4 (EFIO) - Body ground Within 3 seconds of the engine start operation being performed or within 3 seconds of the ignition switch being turned to ON after connecting the cable to the negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

16.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

16.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER ENGINE STARTS
17.CHECK WHETHER ENGINE STARTS
a.

Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the ignition switch to ON.


b.

Check that the engine can be started 5 seconds after the ignition switch turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for M15A-FKS) B
NG (for G16E-GTS) C
NG (for 1KR-FE) D



A

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

B

C

D

18.CHECK ECM

Pre-procedure1

a.

Disconnect the A54 ECM connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-47 (IMO) - Body ground Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Post-procedure1

c.

None


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

19.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

19.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

Pre-procedure1

a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-47 (IMO) - H67-3 (EFII) Always Below 1 Ω
A54-47 (IMO) or H67-3 (EFII) - Other terminals and body ground Always 10 kΩ or higher
A54-61 (IMI) - H67-4 (EFIO) Always Below 1 Ω
A54-61 (IMI) or H67-4 (EFIO) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK ECM

Pre-procedure1

a.

Disconnect the A106 ECM connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A106-47 (IMO) - Body ground Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Post-procedure1

c.

None


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

21.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

21.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

Pre-procedure1

a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-47 (IMO) - H67-3 (EFII) Always Below 1 Ω
A54-47 (IMO) or H67-3 (EFII) - Other terminals and body ground Always 10 kΩ or higher
A54-61 (IMI) - H67-4 (EFIO) Always Below 1 Ω
A54-61 (IMI) or H67-4 (EFIO) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK ECM

Pre-procedure1

a.

Disconnect the A55 ECM connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-43 (IMO) - Body ground Ignition switch turned to ON using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Post-procedure1

c.

None


Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

23.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

23.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

Pre-procedure1

a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-43 (IMO) - H67-3 (EFII) Always Below 1 Ω
A55-43 (IMO) or H67-3 (EFII) - Other terminals and body ground Always 10 kΩ or higher
A55-42 (IMI) - H67-4 (EFIO) Always Below 1 Ω
A55-42 (IMI) or H67-4 (EFIO) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

Pre-procedure1

a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A54 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-47 (IMO) - H67-3 (EFII) Always Below 1 Ω
A54-47 (IMO) or H67-3 (EFII) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

Pre-procedure1

a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A106 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A106-47 (IMO) - H67-3 (EFII) Always Below 1 Ω
A106-47 (IMO) or H67-3 (EFII) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

Pre-procedure1

a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A55 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-43 (IMO) - H67-3 (EFII) Always Below 1 Ω
A55-43 (IMO) or H67-3 (EFII) - Other terminals and body ground Always 10 kΩ or higher



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR