Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › 2020.09–2021.11
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  Steering Lock does not Lock  


DESCRIPTION

The steering lock ECU (steering lock actuator or upper bracket assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little, as is done for a vehicle with a mechanical key, to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Steering Lock does not Lock
Entry&Start
·

Steering Lock Request Receive

·

L Code Check

·

S Code Check*1


Main Body
·

FR Door Courtesy Switch Status

·

FL Door Courtesy Switch Status

·

RR Door Courtesy Switch Status

·

RL Door Courtesy Switch Status


Power Source Control
·

Shift P Signal*2



*1: w/o Wireless Door Lock Buzzer Answer-back Function

*2: for CVT


WIRING DIAGRAM

C396309E38
3.281,2.792 3.594,2.99 0.313,0.198 10 false 24 3.281,3.229 3.594,3.427 0.313,0.198 10 false 11 3.281,3.885 3.594,4.083 0.313,0.198 10 false 29 5.177,0.25 5.49,0.448 0.313,0.198 10 false 7 5.167,2.802 5.479,3 0.313,0.198 10 false 3 5.167,3.219 5.479,3.417 0.313,0.198 10 false 4 5.177,3.875 5.49,4.073 0.313,0.198 10 false 1 2.531,0.313 4.302,0.563 1.771,0.25 10 false from Auxiliary Battery 4.521,0.479 5.167,0.708 0.646,0.229 10 false AM1*1 0.25,4.375 1.375,4.99 1.125,0.615 10 false Shift Lock Control Unit Assembly*4 2.125,4.396 2.583,4.594 0.458,0.198 10 false H46 2.115,4.563 3.646,5.083 1.531,0.521 10 false Certification ECU (Smart Key ECU Assembly) 4.5,4.385 4.958,4.583 0.458,0.198 10 false H71 4.49,4.552 7.156,5.073 2.667,0.521 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 1.01,3.75 1.625,3.948 0.615,0.198 10 false P2 2.833,2.927 3.448,3.125 0.615,0.198 10 false SLR+ 2.896,3.365 3.208,3.531 0.313,0.167 10 false SLP 3.063,4 3.677,4.198 0.615,0.198 10 false E 5.375,0.354 5.99,0.552 0.615,0.198 10 false B 5.375,2.917 5.99,3.115 0.615,0.198 10 false IGE 5.375,3.354 5.99,3.552 0.615,0.198 10 false SLP1 5.375,4 5.99,4.198 0.615,0.198 10 false GND 2.438,3.76 2.677,3.948 0.24,0.188 10 false P 0.646,5.281 2.521,5.563 1.875,0.281 10 false : LIN Communication Line 2.177,3.625 2.635,3.823 0.458,0.198 10 false 14 1.292,3.625 1.75,3.885 0.458,0.26 10 false 3 0.26,4.219 0.875,4.417 0.615,0.198 10 false H20 4.094,0.677 5.406,1 1.313,0.323 10 false STRG LOCK*2, *3 2.26,5.167 4.135,5.448 1.875,0.281 10 false *1: for TMC Made with 5 Door 4.115,5.167 6.313,5.427 2.198,0.26 10 false *2: for TMMF Made 0.333,2.823 1.917,3.26 1.583,0.438 10 false ID Code Box (Immobiliser Code ECU)*5 6.281,5.167 7.156,5.375 0.875,0.208 10 false *4: for CVT 0.323,2.635 0.938,2.833 0.615,0.198 10 false H67 1.698,3.625 2.01,3.823 0.313,0.198 10 false *4 4.073,1.625 4.385,1.823 0.313,0.198 10 false *5 2.25,5.458 6.771,5.719 4.521,0.26 10 false *5: w/o Wireless Door Lock Buzzer Answer-back Function 5.354,5.167 6.594,5.354 1.24,0.188 10 false *3: for 3 Door

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the ignition switch to ACC or ON.

-

To lock the steering, turn the ignition switch off with the shift lever in P (for CVT), and then open a door.


·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, confirm that the problem does not recur.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Request Receive Status of steering lock command from certification ECU (smart key ECU assembly) OK or NG
for CVT:

OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and ignition switch off)

NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and ignition switch off)


for Manual Transaxle:

OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with ignition switch off)

NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with ignition switch off)


If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Steering Lock Request Receive
50003 440 63
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the ignition switch from ON to ACC or off and opening a door with the shift lever in P (for CVT), and OK is displayed on the GTS screen.



Result:
Result Proceed to
OK (w/ Wireless Door Lock Buzzer Answer-back Function) A
OK (w/o Wireless Door Lock Buzzer Answer-back Function) B
NG C



A

2.READ VALUE USING GTS (L CODE CHECK)

B

9.READ VALUE USING GTS (S CODE CHECK)

C

11.READ VALUE USING GTS (DOOR COURTESY SW)
2.READ VALUE USING GTS (L CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check
w/ Wireless Door Lock Buzzer Answer-back Function:

Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly)


w/o Wireless Door Lock Buzzer Answer-back Function:

Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly)


OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
w/ Wireless Door Lock Buzzer Answer-back Function:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


w/o Wireless Door Lock Buzzer Answer-back Function:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 440 61
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.


*1: w/ Wireless Door Lock Buzzer Answer-back Function

*2: w/o Wireless Door Lock Buzzer Answer-back Function




Result:
Result Proceed to
OK A
NG (w/ Wireless Door Lock Buzzer Answer-back Function) B
NG (w/o Wireless Door Lock Buzzer Answer-back Function) C



A

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

C

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C435465C02
1.5,1.031 1.917,1.281 0.417,0.25 0.958,1.667 1.208,1.667 1.208,1.667 1.208,2.417 true 2.458,1.667 2.208,1.667 2.208,1.667 2.208,2.417 true 0.323,0.208 0.635,0.365 0.313,0.156 10 false *a 1.583,1.073 1.896,1.229 0.313,0.156 10 false H71 0.625,1.583 1.104,1.781 0.479,0.198 10 false GND 2.5,1.583 2.813,1.74 0.313,0.156 10 false B
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H71-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Connect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C396300C20
0.323,2.906 1.646,3.042 1.323,0.135 2.344,2.948 2.75,3.073 0.406,0.125 1.615,4.063 2.375,4.177 0.76,0.115 1.531,0.177 1.969,0.406 0.438,0.229 0.896,3.25 0.896,3.042 false 2.573,3.281 2.573,3.073 false 2.01,4.063 2.01,3.854 false 0.813,1.802 1.875,1.104 true 2.792,1.646 2.302,1.083 true 0.271,0.26 0.583,0.417 0.313,0.156 10 false *a 0.823,3.281 1.135,3.438 0.313,0.156 10 false *b 1.917,3.688 2.229,3.844 0.313,0.156 10 false *c 2.5,3.302 2.813,3.458 0.313,0.156 10 false *b 0.646,1.854 1.104,2.052 0.458,0.198 10 false IGE 2.76,1.698 3.219,1.896 0.458,0.198 10 false GND 2.969,4.083 3.427,4.281 0.458,0.198 10 false GND 1.635,0.219 2.094,0.417 0.458,0.198 10 false H71
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Content
Tester Connection H71-3 (IGE) - H71-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P*1

·

Steering unlocked

·

Ignition switch turned off



*1: for CVT



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-3 (IGE) - H46-24 (SLR+) Always Below 1 Ω
H71-3 (IGE) or H46-24 (SLR+) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


e.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

6.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Connect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
B518305C12
1.49,0.99 1.896,1.25 0.406,0.26 2.354,2.885 1.885,2.885 1.885,2.885 1.885,1.979 true 0.188,0.281 0.5,0.438 0.313,0.156 10 false *a 1.573,1.031 2.073,1.302 0.5,0.271 10 false H71 2.448,2.802 2.948,3.073 0.5,0.271 10 false IGE
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H71-3 (IGE) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 440 61
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 440 61
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

9.READ VALUE USING GTS (S CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check S code verification result OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 440 60
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (L CODE CHECK)

NG

10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check S code verification result OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 440 60
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

11.READ VALUE USING GTS (DOOR COURTESY SW)
a.

Using the GTS, check the following main body ECU (multiplex network body ECU) Data List item by opening and closing the each door to confirm the state of the each door courtesy light switch assembly.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Switch Status Front door RH courtesy light switch signal OFF or ON OFF: Front door RH closed
ON: Front door RH open
-
FL Door Courtesy Switch Status Front door LH courtesy light switch signal OFF or ON OFF: Front door LH closed
ON: Front door LH open
-
RR Door Courtesy Switch Status Rear door RH courtesy light switch signal* OFF or ON OFF: Rear door RH closed
ON: Rear door RH open
-
RL Door Courtesy Switch Status Rear door LH courtesy light switch signal* OFF or ON OFF: Rear door LH closed
ON: Rear door LH open
-

*: for 5 Door


Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy Switch Status
FL Door Courtesy Switch Status
RR Door Courtesy Switch Status
RL Door Courtesy Switch Status
50003 449 30,31,32,33
OK:

The Data List item changes in accordance with the opening and closing of the each door.



Result:
Proceed to
OK
NG



OK

12.CONFIRM MODEL

NG

GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit, Rear Door Courtesy Switch Circuit)

12.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for CVT A
for Manual Transaxle B



A

13.READ VALUE USING GTS (SHIFT P SIGNAL)

B

19.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
13.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Move the shift lever to P.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is OFF.


Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 454 205
OK:

ON is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)

NG

16.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
14.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Request Receive Status of steering lock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and ignition switch off)
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Steering Lock Request Receive
50003 440 63
OK:

Within 10 seconds after any of the doors is opened with shift lever in P and ignition switch off, the Data List item changes to "OK".



Result:
Result Proceed to
OK A
NG (w/ Wireless Door Lock Buzzer Answer-back Function) B
NG (w/o Wireless Door Lock Buzzer Answer-back Function) C



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

C

15.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
15.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Request Receive Status of steering lock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and ignition switch off)
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Steering Lock Request Receive
50003 440 63
OK:

Within 10 seconds after any of the doors is opened with shift lever in P and ignition switch off, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

16.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B574624C13
1.583,0.042 1.979,0.25 0.396,0.208 2.271,1.885 2.146,1.885 2.146,1.885 1.698,0.792 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.667,0.073 1.979,0.271 0.313,0.198 10 false H46 2.333,1.802 2.698,1.99 0.365,0.188 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-14 (P) - Body ground Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H20 shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-14 (P) - H20-3 (P2) Always Below 1 Ω
H46-14 (P) or H20-3 (P2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

18.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B574624C14
1.583,0.042 1.979,0.25 0.396,0.208 2.271,1.885 2.146,1.885 2.146,1.885 1.698,0.792 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.667,0.073 1.979,0.271 0.313,0.198 10 false H46 2.333,1.802 2.698,1.99 0.365,0.188 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-14 (P) - Body ground Shift lever in P 9 V or higher



Result:
Result Proceed to
OK (for TMC Made) A
OK (for TMMF Made) B
NG C



A

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

B

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

19.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Request Receive Status of steering lock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with ignition switch off)
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Steering Lock Request Receive
50003 440 63
OK:

Within 10 seconds after any of the doors is opened with ignition switch off, the Data List item changes to "OK".



Result:
Result Proceed to
OK A
NG (w/ Wireless Door Lock Buzzer Answer-back Function) B
NG (w/o Wireless Door Lock Buzzer Answer-back Function) C



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

C

20.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
20.READ VALUE USING GTS (STEERING LOCK REQUEST RECEIVE)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY

HINT:

Refer to Service Bulletin.



b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Request Receive Status of steering lock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and ignition switch off)
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Steering Lock Request Receive
50003 440 63
OK:

Within 10 seconds after any of the doors is opened with shift lever in P and ignition switch off, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)