Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › from 2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser function compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

WIRING DIAGRAM

w/ Wireless Door Lock Buzzer Answer-back Function


C375433E35
5.573,2.76 6.688,3 1.115,0.24 10 false A54*1, A106*2 5.583,2.917 6.125,3.135 0.542,0.219 10 false ECM 5.813,1.26 6.271,1.458 0.458,0.198 10 false +B 5.313,0.813 5.771,1.01 0.458,0.198 10 false IMO 5.313,1.719 5.771,1.917 0.458,0.198 10 false IMI 5.021,0.813 5.375,1.094 0.354,0.281 10 false 47 5.021,1.729 5.302,1.99 0.281,0.26 10 false 61 1.573,0.792 2.135,1.01 0.563,0.219 10 false EFII 1.531,1.76 1.99,1.958 0.458,0.198 10 false EFIO 1.979,0.813 2.438,1.01 0.458,0.198 10 false 4 1.99,1.74 2.448,1.938 0.458,0.198 10 false 5 0.698,0.26 1.156,0.458 0.458,0.198 10 false +B 0.208,2.833 0.667,3.031 0.458,0.198 10 false H45 0.198,3 3.052,3.271 2.854,0.271 10 false Certification ECU (Smart Key ECU Assembly) 3,3.417 5.448,3.615 2.448,0.198 10 false *1: for M15A-FKS 4.344,3.417 6.167,3.604 1.823,0.188 10 false *2: for G16E-GTS


w/o Wireless Door Lock Buzzer Answer-back Function


C375433E36
5.375,2.76 6.906,2.979 1.531,0.219 10 false A54*1, A55*2, A106*3 5.375,2.927 5.917,3.146 0.542,0.219 10 false ECM 5.813,1.26 6.271,1.458 0.458,0.198 10 false +B 5.313,0.813 5.771,1.01 0.458,0.198 10 false IMO 5.313,1.719 5.771,1.917 0.458,0.198 10 false IMI 4.396,0.813 5.323,1.01 0.927,0.198 10 false 47*1*3, 43*2 4.406,1.719 5.292,1.917 0.885,0.198 10 false 61*1*3, 42*2 1.573,0.792 2.135,1.01 0.563,0.219 10 false EFII 1.531,1.76 1.99,1.958 0.458,0.198 10 false EFIO 1.979,0.813 2.438,1.01 0.458,0.198 10 false 3 1.99,1.74 2.448,1.938 0.458,0.198 10 false 4 0.698,0.26 1.156,0.458 0.458,0.198 10 false +B 0.208,2.833 0.667,3.031 0.458,0.198 10 false H67 0.198,3 3.052,3.271 2.854,0.271 10 false ID Code Box (Immobiliser Code ECU) 2.646,3.302 4.042,3.521 1.396,0.219 10 false *1: for M15A-FKS 3.948,3.302 5.344,3.521 1.396,0.219 10 false *2: for 1KR-FE 5.042,3.302 6.438,3.521 1.396,0.219 10 false *3: for G16E-GTS


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ECM or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If an immobiliser function or engine DTC is output, first perform troubleshooting for the immobiliser function or engine DTC.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CONFIRM MODEL

B

2.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Wireless Door Lock Buzzer Answer-back Function A
w/o Wireless Door Lock Buzzer Answer-back Function B



A

3.CHECK CERTIFICATION ECU ((SMART KEY ECU ASSEMBLY) (TERMINAL EFIO AND EFII))

B

11.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
3.CHECK CERTIFICATION ECU ((SMART KEY ECU ASSEMBLY) (TERMINAL EFIO AND EFII))
a.

Using an oscilloscope, check the waveform.

B574906C03
2.135,0.208 2.552,0.406 0.417,0.198 3.083,1.823 2.917,1.823 2.917,1.823 2.01,0.792 true 1.917,0.802 1.406,1.781 1.406,1.781 1.24,1.781 true 3,3.646 3,4.229 3,4.229 2.833,4.229 true 3.167,3.635 3.167,4.219 3.167,4.219 3.333,4.219 true 3.583,5.698 3.583,6.135 3.583,6.135 3.75,6.135 true 3.417,5.688 3.417,6.26 3.417,6.26 3.583,6.26 true 0.25,0.219 0.563,0.375 0.313,0.156 10 false *a 2.656,4.146 2.969,4.302 0.313,0.156 10 false *b 3.354,4.146 3.667,4.302 0.313,0.156 10 false *c 3.646,6.208 3.958,6.365 0.313,0.156 10 false *d 3.667,7.375 3.979,7.531 0.313,0.156 10 false *e 1.375,2.427 1.688,2.583 0.313,0.156 10 false *f 1.375,4.448 1.688,4.604 0.313,0.156 10 false *g 2.417,4.646 2.729,4.802 0.313,0.156 10 false *h 3.031,2.698 3.344,2.854 0.313,0.156 10 false *i 3.458,4.615 3.771,4.771 0.313,0.156 10 false *j 1.458,6.49 1.771,6.646 0.313,0.156 10 false *k 3.177,1.74 3.792,1.938 0.615,0.198 10 false EFII 3.792,6.073 4.104,6.229 0.313,0.156 10 false *c 3.74,7.125 4.052,7.281 0.313,0.156 10 false *d 1.854,7.135 2.167,7.292 0.313,0.156 10 false *d 1.948,7.385 2.26,7.542 0.313,0.156 10 false *e 1.031,5.646 1.396,5.906 0.365,0.26 10 false GND 1.021,3.615 1.385,3.875 0.365,0.26 10 false GND 0.917,1.719 1.531,1.917 0.615,0.198 10 false EFIO 2.229,0.219 2.844,0.417 0.615,0.198 10 false H45
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Approximately 160 ms.
*c Approximately 270 ms. *d Approximately 40 ms.
*e Approximately 60 ms. *f Waveform (EFII)
*g Waveform (EFIO) *h Waveform 1
*i Waveform 2 *j Waveform 3
*k Waveform 1 (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:
Tester Connection Condition Tool Setting Specified Condition
H45-4 (EFII) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)
H45-5 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1 and 3)



Result:
Result Proceed to
Normal waveform A
Waveform 1 is not output, or has abnormal wavelength or shape B
Waveform 2 is not output, or has abnormal wavelength or shape (for M15A-FKS) C
Waveform 2 is not output, or has abnormal wavelength or shape (for G16E-GTS) D
Waveform 3 is not output, or has abnormal wavelength or shape E



A

4.REGISTER ECU COMMUNICATION ID

B

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

C

D

E

7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER ENGINE STARTS
5.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A54 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-47 (IMO) - H45-4 (EFII) Always Below 1 Ω
A54-47 (IMO) or H45-4 (EFII) - Other terminals and body ground Always 10 kΩ or higher
A54-61 (IMI) - H45-5 (EFIO) Always Below 1 Ω
A54-61 (IMI) or H45-5 (EFIO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


Result:
Proceed to
NEXT



NEXT

8.REGISTER RECOGNITION CODE
8.REGISTER RECOGNITION CODE
a.

Register the recognition codes to the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for M15A-FKS) B
NG (for G16E-GTS) C



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

C

11.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Immobiliser fuel cut status OFF or ON OFF: Fuel cut OFF
ON: Fuel cut ON
-
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut Status
50003 372 65

Result:
Result Proceed to
On the GTS screen, ON is displayed. (for M15A-FKS) A
On the GTS screen, ON is displayed. (for G16E-GTS) B
On the GTS screen, ON is displayed. (for 1KR-FE) C
On the GTS screen, OFF is displayed. D



A

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

D

12.CHECK WHETHER ENGINE STARTS
12.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts after 5 seconds of the ignition switch being turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

13.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO AND EFII)
13.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO AND EFII)
a.

Using an oscilloscope, check the waveform.

E446707C03
3.469,0.406 3.885,0.604 0.417,0.198 4.458,1.917 4.292,1.917 4.292,1.917 3.698,1.188 true 3.583,1.188 3.24,1.896 3.24,1.896 3.073,1.896 true 2.99,3.531 2.99,4.115 2.99,4.115 2.823,4.115 true 3.177,3.531 3.177,4.115 3.177,4.115 3.344,4.115 true 3.583,5.573 3.583,6.01 3.583,6.01 3.75,6.01 true 3.396,5.573 3.396,6.146 3.396,6.146 3.563,6.146 true 0.25,0.219 0.563,0.375 0.313,0.156 10 false *a 2.656,4.031 2.969,4.188 0.313,0.156 10 false *b 3.375,4.021 3.688,4.177 0.313,0.156 10 false *c 3.594,6.073 3.906,6.229 0.313,0.156 10 false *d 3.656,7.219 3.969,7.375 0.313,0.156 10 false *e 1.375,2.292 1.719,2.615 0.344,0.323 10 false *f 1.375,4.323 1.688,4.656 0.313,0.333 10 false *g 2.344,4.51 2.656,4.667 0.313,0.156 10 false *h 3.031,2.594 3.375,2.875 0.344,0.281 10 false *i 3.458,4.49 3.865,4.813 0.406,0.323 10 false *j 1.458,6.49 1.771,6.646 0.313,0.156 10 false *k 4.51,1.833 5.125,2.031 0.615,0.198 10 false EFII 3.792,5.948 4.104,6.104 0.313,0.156 10 false *c 3.719,6.979 4.031,7.135 0.313,0.156 10 false *d 1.844,6.99 2.156,7.146 0.313,0.156 10 false *d 1.927,7.219 2.24,7.375 0.313,0.156 10 false *e 1.031,5.531 1.396,5.792 0.365,0.26 10 false GND 1.021,3.49 1.385,3.75 0.365,0.26 10 false GND 2.708,1.813 3.323,2.01 0.615,0.198 10 false EFIO 3.531,0.427 4.146,0.625 0.615,0.198 10 false H67
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Approximately 160 ms.
*c Approximately 270 ms. *d Approximately 40 ms.
*e Approximately 60 ms. *f Waveform (EFII)
*g Waveform (EFIO) *h Waveform 1
*i Waveform 2 *j Waveform 3
*k Waveform 1 (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:
Tester Connection Condition Tool Setting Specified Condition
H67-3 (EFII) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)
H67-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1 and 3)



Result:
Result Proceed to
Normal waveform A
Waveform 1 is not output, or has abnormal wavelength or shape B
Waveform 2 is not output, or has abnormal wavelength or shape (for M15A-FKS) C
Waveform 2 is not output, or has abnormal wavelength or shape (for G16E-GTS) D
Waveform 2 is not output, or has abnormal wavelength or shape (for 1KR-FE) E
Waveform 3 is not output, or has abnormal wavelength or shape F



A

14.REGISTER ECU COMMUNICATION ID

B

16.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

C

D

E

F

17.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
14.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

15.CHECK WHETHER ENGINE STARTS
15.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

16.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A55 ECM connector.*1


c.

Disconnect the A54 ECM connector.*2


d.

Disconnect the A106 ECM connector.3


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-43 (IMO) - H67-3 (EFII)*1 Always Below 1 Ω
A54-47 (IMO) - H67-3 (EFII)*2 Always Below 1 Ω
A106-47 (IMO) - H67-3 (EFII)*3 Always Below 1 Ω
A55-43 (IMO) or H67-3 (EFII) - Other terminals and body ground*1 Always 10 kΩ or higher
A54-47 (IMO) or H67-3 (EFII) - Other terminals and body ground*2 Always 10 kΩ or higher
A106-47 (IMO) or H67-3 (EFII) - Other terminals and body ground*3 Always 10 kΩ or higher
A55-42 (IMI) - H67-4 (EFIO)*1 Always Below 1 Ω
A54-61 (IMI) - H67-4 (EFIO)*2 Always Below 1 Ω
A106-61 (IMI) - H67-4 (EFIO)*3 Always Below 1 Ω
A55-42 (IMI) or H67-4 (EFIO) - Other terminals and body ground*1 Always 10 kΩ or higher
A54-61 (IMI) or H67-4 (EFIO) - Other terminals and body ground*2 Always 10 kΩ or higher
A106-61 (IMI) or H67-4 (EFIO) - Other terminals and body ground*3 Always 10 kΩ or higher



*1: for 1KR-FE

*2: for M15A-FKS

*3: for G16E-GTS


Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.


Result:
Proceed to
NEXT



NEXT

18.REGISTER RECOGNITION CODE
18.REGISTER RECOGNITION CODE
a.

Register the recognition codes to the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

19.REGISTER ECU COMMUNICATION ID
19.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

20.CHECK WHETHER ENGINE STARTS
20.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for M15A-FKS) B
NG (for G16E-GTS) C
NG (for 1KR-FE) D



A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

B

C

D