Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0434686 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch is pressed, the sensor off signal is sent to the main body ECU (multiplex network body ECU) which causes the theft warning ultrasonic sensor to stop operating.

WIRING DIAGRAM

B424479E15
5.958,0.292 6.271,0.49 0.313,0.198 10 false +B 5.229,0.75 5.844,0.948 0.615,0.198 10 false SSW1 1.604,0.74 2.01,0.938 0.406,0.198 10 false 2 3.875,0.74 4.177,0.927 0.302,0.188 10 false 5 4.99,0.74 5.292,0.927 0.302,0.188 10 false 20 4.969,1.667 5.396,1.854 0.427,0.188 10 false H5 1.844,1.417 2.188,1.604 0.344,0.188 10 false H147 4.969,1.844 6.625,2.25 1.656,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 1.802,0.75 2.146,0.938 0.344,0.188 10 false VV- 3.385,0.74 3.823,0.938 0.438,0.198 10 false SOFF 1.844,1.594 3.823,1.833 1.979,0.24 10 false Intrusion Sensor Cancel Switch

CAUTION / NOTICE / HINT

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*1

*1: w/ Entry and Start System



PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENSOR CANCEL SWITCH)
a.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Cancel Switch Intrusion sensor cancel switch ON or OFF ON: Intrusion sensor cancel switch on
OFF: Intrusion sensor cancel switch off
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor Cancel Switch
50003 449 98
OK:

The indicator on the GTS switches between ON and OFF in accordance with the intrusion sensor cancel switch status.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INTRUSION SENSOR CANCEL SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (INTRUSION SENSOR CANCEL SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the H5 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the H147 intrusion sensor cancel switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H5-20 (SSW1) - H147-5 (SOFF) Always Below 1 Ω
H147-2 (VV-) - Body ground Always Below 1 Ω
H5-20 (SSW1) or H147-5 (SOFF) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR