Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for RHD) › 2020.09–2021.11
RM36W0E _57 Power Source / Network _088265 POWER DISTRIBUTION _0432923 MAIN BODY ECU(for RHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
for HV Model:
Replacement of the main body ECU (multiplex network body ECU)
Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.
ECU configuration - (Click here)
for Gasoline Model:
Replacement of the main body ECU (multiplex network body ECU)
Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, Gasoline model)

·

Entry and start system (for Start function, Gasoline model)

·

Engine start function


See Service Bulletin for the registration method.
ECU configuration - (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55479D 3.REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55432B 4.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55407B 5.REMOVE SWITCH HOLE BASE SUB-ASSEMBLY

Hide 33504F 6.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for CVT)

Hide 33504F 7.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

Hide 33554 8.REMOVE SHIFT LEVER CAP (for CVT)

Hide 58802E 9.REMOVE FRONT CONSOLE BOX SUB-ASSEMBLY (for 5 Door)

Hide 58810J 10.REMOVE CONSOLE BOX ASSEMBLY (for 3 Door)

Hide 67914B 11.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 12.REMOVE COWL SIDE TRIM BOARD LH

Hide 55607 13.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62312B 14.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 55318F 15.REMOVE NO. 2 INSTRUMENT SIDE PANEL

HINT:

Use the same procedure as for the No. 1 side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55550 16.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55433B 17.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 18.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

a.
B579706

Disconnect the 7 connectors.


b.

Disengage the clamps.


c.
B579705C01
2.302,0.729 2.479,0.552 false 2.438,1.458 2.781,1.406 true 2.219,0.74 2.531,0.938 0.313,0.198 10 false *a 2.271,1.385 2.583,1.583 0.313,0.198 10 false *a
*a Lock Lever


Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.


d.

Disengage the clamp.


e.

for HV Model:

i.
B578676C01
0.698,0.563 0.552,0.771 false 1.01,1.396 0.646,1.49 true 0.469,0.781 0.781,0.979 0.313,0.198 10 false *a 0.469,1.417 0.781,1.615 0.313,0.198 10 false *a
*a Lock Lever


Disengage the clamp.


ii.

Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.



f.
B579704

Disconnect the 4 connectors.


g.
E438393C01
1.031,0.75 0.771,0.448 true 0.594,0.333 0.906,0.49 0.313,0.156 10 false *a
*a Protective Tape


Remove the bolt and 2 nuts.


h.

Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


i.

Pull out the instrument panel junction block assembly with multiplex network body ECU.


j.
E438568

Disengage the claws.


k.
B578677C01
0.531,0.552 0.375,0.74 false 0.844,1.417 0.542,1.5 true 0.313,0.76 0.625,0.958 0.313,0.198 10 false *a 0.354,1.427 0.667,1.625 0.313,0.198 10 false *a
*a Protective Tape


Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.


l.

Remove the instrument panel junction block assembly with multiplex network body ECU.


Hide 82730G 19.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

a.
E438399

Remove the bolt.


b.

Disengage the clamp to remove the instrument panel junction block assembly from the ECU integration box LH.


Hide 89221 20.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E438385C01
0.677,1.146 0.875,1.365 true 0.208,1.052 0.583,1.052 true 0.906,1.302 1.219,1.5 0.313,0.198 10 false *1 0.01,0.958 0.323,1.156 0.313,0.198 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100135

Push


Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.


b.
E438386C01
1.542,1.708 1.729,1.479 true 1.427,1.698 1.74,1.854 0.313,0.156 10 false *a
*a Protective Tape
V100135

Insert
V113147

Raise in this Direction


With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped in protective tape horizontally between the main body ECU (multiplex network body ECU) and the instrument panel junction block assembly.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).




c.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



d.
E438387C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the main body ECU (multiplex network body ECU) as shown in the illustration.

NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.