Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0434686 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Circuit  


DESCRIPTION

If no warnings operate or the system can be set even though the conditions to set the system are not met, the main body ECU (multiplex network body ECU) cannot perform recognition due to a cutoff of the ON signal from the courtesy light switch from the doors, engine hood or back door, or some other problem.

If the automatic alarm operates when it should not operate, it may be due to a false detection by the intrusion sensor (theft warning ultrasonic sensor) or due to the ON signal being input when there is a short circuit in the courtesy light switch of the doors, engine hood or back door, or some other problem which would cause this to happen.

HINT:

In the following situations, the intrusion sensor (theft warning ultrasonic sensor) may operate and cause the automatic alarm system to operate even when the sensor is normal.

·

The driver steps away from the vehicle while other people, pets, etc. are in the vehicle.

·

There are things which move easily inside the vehicle, such as things hanging inside the vehicle or clothing hanging from the coat hooks.

·

Any window is open.

·

The vehicle is parked in a place with a lot of vibration or noise such as a parking garage.

·

The vehicle is being washed using a high-pressure spray gun or an automatic car washing machine.

·

The vehicle is continuously being struck or is vibrating due to hail or lightning.

·

The vehicle is continuously being subjected to impacts or is vibrating when snow or ice is being removed from the vehicle.

·

A frost prevention sheet which has an aluminum film is moved by wind, etc.



WIRING DIAGRAM

E452937E02
5.854,1.083 6.469,1.281 0.615,0.198 10 false LIN4 5.49,1.719 7.115,2.25 1.625,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 5.49,1.542 6.104,1.74 0.615,0.198 10 false H5 5.531,0.896 6.146,1.094 0.615,0.198 10 false 11 3.292,1.771 4.469,2.052 1.177,0.281 10 false Rain Sensor*1 2.938,4.229 4.635,4.5 1.698,0.271 10 false *1: w/ Rain Sensor 0.75,4.24 2.708,4.51 1.958,0.271 10 false : LIN Communication Line 3.292,1.604 3.906,1.802 0.615,0.198 10 false V9 3.781,1.073 4.396,1.271 0.615,0.198 10 false MPX 4.219,0.906 4.833,1.104 0.615,0.198 10 false 3 3.813,2.469 4.427,2.667 0.615,0.198 10 false LIN1 3.792,2.906 4.406,3.104 0.615,0.198 10 false GND 4.198,2.781 4.813,2.979 0.615,0.198 10 false 3 4.198,2.313 4.813,2.51 0.615,0.198 10 false 2 3.052,2.573 3.667,2.771 0.615,0.198 10 false 1 3.26,2.688 3.875,2.885 0.615,0.198 10 false +B 3.125,3.188 3.74,3.385 0.615,0.198 10 false V14 3.135,3.375 5.073,3.792 1.938,0.417 10 false Intrusion Sensor (Theft Warning Ultrasonic Sensor) 1.958,2.823 3.135,3.104 1.177,0.281 10 false ECU-DDC NO. 2 0.135,2.667 1.667,3.042 1.531,0.375 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*1

*1: w/ Entry and Start System




PROCEDURE

1.READ VALUE USING GTS (COMMUNICATION INTRUSION SENSOR)
a.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition
Communication Intrusion Sensor 1 Theft warning ultrasonic sensor1 connecting STOP or OK OK: Theft warning ultrasonic sensor connected
STOP: Theft warning ultrasonic sensor not connected
Communication Intrusion Sensor 2 Theft warning ultrasonic sensor2 connecting STOP or OK OK: Theft warning ultrasonic sensor connected
STOP: Theft warning ultrasonic sensor not connected
Body Electrical > Main Body > Data List
Tester Display
Communication Intrusion Sensor 1
Communication Intrusion Sensor 2
50003 449 1655,1656
OK:

"OK" appears on GTS screen.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))
a.

Disconnect the H5 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the V14 intrusion Sensor (theft warning ultrasonic sensor) connector.


c.

Disconnect the V9 rain sensor*1 connector.

*1: w/ Rain Sensor



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H5-11 (LIN4) - V14-23 (LIN1) Always Below 1 Ω
H5-11 (LIN4) or V14-2 (LIN1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)
a.

Replace the intrusion sensor (Theft warning ultrasonic sensor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>INTRUSION SENSOR>REMOVAL


b.

Read the Data List according to the display on the GTS.

HINT:

When performing the above inspection, have the electrical key transmitter sub-assembly in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).


NOTICE:

Make sure that all windows are closed.



c.

From inside the vehicle, put your hand in front of the intrusion sensor (theft warning ultrasonic sensor) and move it back and forth a distance of 0.3 m (0.984 ft.) and check the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition
Communication Intrusion Sensor 1 Theft warning ultrasonic sensor1 connecting STOP or OK OK: Theft warning ultrasonic sensor connected
STOP: Theft warning ultrasonic sensor not connected
Communication Intrusion Sensor 2 Theft warning ultrasonic sensor2 connecting STOP or OK OK: Theft warning ultrasonic sensor connected
STOP: Theft warning ultrasonic sensor not connected
Body Electrical > Main Body > Data List
Tester Display
Communication Intrusion Sensor 1
50003 449 1655
OK:

The GTS display changes correctly in response to the detection condition of the intrusion sensor (theft warning ultrasonic sensor).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)