Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2020.09
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447812 REAR CRANKSHAFT OIL SEAL A

G16E-GTS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not allow MP grease to contact the dust seal.




c.
A479677C01
0.927,1.396 0.51,0.854 0.51,0.854 1.313,0.792 true 0.198,0.771 0.656,0.969 0.458,0.198 10 false SST 1.833,2.792 2.146,2.99 0.313,0.198 10 false *a
*a -0.9 to 1.1 mm


Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07150)

Standard Depth:

-0.9 to 1.1 mm (-0.0354 to 0.0433 in.) (From the edge of the cylinder block sub-assembly and stiffening crankcase assembly)


NOTICE:

Do not tap in the rear engine oil seal at an angle.



Hide 19315 2.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A479675C01
2.729,1.208 1.813,1.208 true 2.781,1.115 3.094,1.313 0.313,0.198 10 false *a
*a Pin


Install the No. 1 crankshaft position sensor plate.

HINT:

Align the pin hole of the No. 1 crankshaft position sensor plate with the pin of the crankshaft.



Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY

a.
A479673N01
1.115,1.385 1.583,1.698 1.583,1.698 1.427,1.292 true 1.635,1.615 2.01,1.802 0.375,0.188 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


b.

Clean the bolt holes.


c.
A479674N01
1.74,0.292 1.896,0.49 0.156,0.198 10 true 1 1.552,1.719 1.708,1.917 0.156,0.198 10 true 2 1.229,0.375 1.385,0.573 0.156,0.198 10 true 3 2.083,1.594 2.24,1.792 0.156,0.198 10 true 4 0.917,0.885 1.073,1.083 0.156,0.198 10 true 5 2.354,1.115 2.51,1.313 0.156,0.198 10 true 6 1.042,1.427 1.198,1.625 0.156,0.198 10 true 7 2.25,0.625 2.406,0.823 0.156,0.198 10 true 8

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
115 N*m (1173 kgf*cm, 85 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.



Hide 31250 4.INSTALL CLUTCH DISC ASSEMBLY