Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2020.09
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447812 REAR CRANKSHAFT OIL SEAL A

G16E-GTS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear engine oil seal removal/installation are shown below.

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 31250 1.REMOVE CLUTCH DISC ASSEMBLY

Hide 13405 2.REMOVE FLYWHEEL SUB-ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A479673N01
1.115,1.385 1.583,1.698 1.583,1.698 1.427,1.292 true 1.635,1.615 2.01,1.802 0.375,0.188 10 true SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A479674

Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly.


Hide 19315 3.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A479675

Remove the No. 1 crankshaft position sensor plate.


Hide 11401L 4.REMOVE REAR ENGINE OIL SEAL

a.
A479676C01
2.99,1.458 3.177,0.771 true 1.781,1.552 1.51,1.229 true 2.917,1.49 3.229,1.688 0.313,0.198 10 false *b 1.844,1.51 2.063,1.708 0.219,0.198 10 true *a
*a Protective Tape
*b Cut Position


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.


HINT:

Tape the screwdriver tip before use.