Home › Drivetrain › CLUTCH › CLUTCH UNIT (for EA67F) › from 2020.09
RM36W0E _52 Drivetrain _089426 CLUTCH _0447224 CLUTCH UNIT(for EA67F) A

CLUTCH  CLUTCH UNIT(for EA67F)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during cover and disc clutch set removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Engine assembly

·

Air intake system parts

·

Exhaust system parts

·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Tire ECU Data Initialization (When performing tire replacement after RoB code X2104 is output) Active torque split AWD system (Click here)
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 31483 2.REMOVE BLEEDER CLUTCH RELEASE TUBE

a.
C450373

Using a 10 mm union nut wrench, separate the bleeder clutch release tube from the clutch release bleeder sub-assembly.


b.

Remove the bolt and bleeder clutch release tube from the manual transaxle assembly.


c.
C450374

Remove the clamp from the bleeder clutch release tube.


Hide 31407B 3.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C450660

Using a 10 mm union nut wrench, separate the clutch release bleeder sub-assembly from the clutch release cylinder to bleeder tube.


b.
C450661

Remove the bolt and clutch release bleeder sub-assembly from the manual transaxle assembly.


Hide 31224 4.REMOVE CLUTCH RELEASE BEARING PLATE

a.
C450662

Remove the clutch release bearing plate from the manual transaxle assembly.

NOTICE:

When removing the manual transaxle assembly, the clutch release bearing plate could fall out.



Hide 31400 5.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

a.
C450663

Remove the clutch tube boot from the manual transaxle assembly.


b.
C450664

Remove the 3 bolts and clutch release cylinder with bearing assembly together with clutch release cylinder to bleeder tube from the manual transaxle assembly.


Hide 31483 6.REMOVE CLUTCH RELEASE CYLINDER TO BLEEDER TUBE

a.

Mount the clutch release cylinder with bearing assembly in a soft jaw vise.


b.
C450665

Using a 10 mm union nut wrench, remove the clutch release cylinder to bleeder tube from the clutch release cylinder with bearing assembly.


Hide 31001 7.REMOVE COVER AND DISC CLUTCH SET

a.
C450666C01
1.031,0.719 1.448,0.302 false 1.052,0.896 0.594,1.115 0.594,1.115 0.979,0.854 true 0.469,1.094 0.781,1.25 0.313,0.156 10 false *a
*a Match mark


Put match marks on the clutch cover assembly and the flywheel sub-assembly.


b.

Loosen each bolt 180° at a time until the spring tension is released.


c.

Remove the 6 bolts and pull off the cover and disc clutch set.

NOTICE:
·

Do not drop the clutch disc assembly.

·

Keep the lined part of the clutch disc assembly, the pressure plate, and the surface of the flywheel sub-assembly away from oil and foreign matter.