Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › CYLINDER BLOCK › 2020.09–2021.11
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447816 CYLINDER BLOCK A

G16E-GTS ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1570A 1.INSTALL NO. 3 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 3 No. 3 oil nozzle sub-assemblies to the cylinder block sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15709 2.INSTALL NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 3 No. 2 oil nozzle sub-assemblies to the cylinder block sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 3 No. 1 oil nozzle sub-assemblies to the cylinder block sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 4.INSTALL PISTON

HINT:

Perform inspection after repair after replacing the piston.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Using a screwdriver, install a new piston pin hole snap ring to the piston pin hole on the rear side of the piston.

NOTICE:

Be sure that the end gap of the piston pin hole snap ring is not aligned with the cutout of the piston.


HINT:

Tape the screwdriver tip before use.



b.

Gradually heat the piston to between 80 and 90°C (176 and 194°F).

CAUTION:

Be sure to wear protective gloves.



c.

Apply a light coat of engine oil to the piston, piston pin and connecting rod.


d.
A479889C01
0.885,1.333 1.385,0.479 true 1.177,2.573 0.656,2.177 0.656,2.177 0.813,2.583 true 1.365,0.323 1.677,0.479 0.313,0.156 10 false *a 0.438,2.083 0.75,2.24 0.313,0.156 10 false *b
*a Cutout
*b Front Mark


Align the cutout of the piston and front mark of the connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the piston pin comes into contact with the piston pin hole snap ring.

NOTICE:

Do not change the combination of the pistons and piston pins.



e.
A479888C01
0.729,1.615 1.167,1.615 true 0.76,1.885 1.198,1.885 true 1.917,0.969 2.083,1.396 2.083,1.396 2.323,1.396 true 0.573,1.792 0.885,1.99 0.313,0.198 10 false *a 0.573,1.521 0.885,1.719 0.313,0.198 10 false *1 2.365,1.313 2.677,1.51 0.313,0.198 10 false *b
*1 Piston Pin Hole Snap Ring
*a Cutout
*b Protective Tape


Using a screwdriver, install a new piston pin hole snap ring to the piston pin hole on the front side of the piston.

NOTICE:

Be sure that the end gap of the piston pin hole snap ring is not aligned with the cutout of the piston.


HINT:

Tape the screwdriver tip before use.



f.
A479890

Check the fitting condition between the piston and piston pin.

i.

Move the connecting rod back and forth on the piston pin. Check the fitting condition.

HINT:

If abnormal movement is felt, replace the piston and piston pin as a set.



ii.

Rotate the piston back and forth on the piston pin. Check the fitting condition.

HINT:

If abnormal movement is felt, replace the piston and piston pin as a set.




Hide 13011 5.INSTALL PISTON RING SET

HINT:

Perform inspection after repair after replacing the piston and piston ring.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A479891C01
2.823,0.844 3.01,0.719 false 2.76,1.104 2.958,1.104 false 2.823,1.375 2.99,1.479 false 3.052,0.594 3.365,0.75 0.313,0.156 10 false *1 3.01,1.021 3.323,1.177 0.313,0.156 10 false *2 3.042,1.427 3.354,1.583 0.313,0.156 10 false *3
*1 Upper Side Rail
*2 Oil Ring Expander
*3 Lower Side Rail


Install the oil ring expander by hand.


b.
A435910C06
0.531,0.24 0.698,0.708 false 1.333,1.938 1.292,1.406 false 0.323,0.052 1.094,0.25 0.771,0.198 10 false *1,*2 1.26,1.969 1.573,2.167 0.313,0.198 10 false *a
*1 Upper Side Rail
*2 Lower Side Rail
*a Code Mark (T)


Install upper side rail and lower side rail to the piston.

NOTICE:

Install the upper side rail and lower side rail with the code mark (T) facing upward.



c.

Check that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.

A479892C01
1.875,0.615 2.188,0.813 0.313,0.198 10 false *a 3.646,0.854 3.958,1.052 0.313,0.198 10 false *c 3.625,2.292 3.938,2.49 0.313,0.198 10 false *d 4.375,1.792 4.688,1.99 0.313,0.198 10 false *b
*a Press around the circumference *b Ring End
*c Correct *d Incorrect (Ends of the oil ring expander are overlapping)


NOTICE:
·

After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.

·

If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.

·

If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander.




d.
A479893C01
0.76,2.594 0.469,2.458 false 0.698,3.24 0.406,3.104 false 1.563,2.385 2.104,2.99 2.104,2.99 1.604,2.958 true 0.958,4.135 0.771,3.906 false 2.323,4.115 2.563,3.896 false 0.26,2.333 0.573,2.49 0.313,0.156 10 false *1 0.229,2.99 0.542,3.146 0.313,0.156 10 false *2 2.156,2.927 2.469,3.083 0.313,0.156 10 false *a 0.625,3.771 0.938,3.927 0.313,0.156 10 false *1 2.625,3.771 2.938,3.927 0.313,0.156 10 false *2
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*a Code Mark
V100135

Upward


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring with the code mark positioned as shown in the illustration.

Piston Ring Mark:
Item Code Mark Paint Mark
No. 1 Compression Ring T -
No. 2 Compression Ring 2T -


NOTICE:

Install the compression rings with the code marks facing upward.



e.
A479894C01
1.76,1.813 1.281,1.969 1.281,1.969 1.896,1.823 true 2.052,0.01 2.542,0.198 0.49,0.188 10 false *1, *4 2.052,1.99 2.542,2.177 0.49,0.188 10 false *2, *5 0.813,1.01 1.125,1.208 0.313,0.198 10 false *3 1.052,1.896 1.365,2.094 0.313,0.198 10 false *a
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Upper Side Rail
*5 Lower Side Rail
*a Front Mark
V100136

Front of Engine


Position the piston rings so that the ring ends are as shown in the illustration.


Hide 11711 6.INSTALL CRANKSHAFT BEARING

a.

Clean the main journal and both surfaces of the No. 1 crankshaft bearings and No. 2 crankshaft bearings.


b.
A479895

Install the 4 No. 1 crankshaft bearings to the cylinder block sub-assembly as shown in the illustration.

NOTICE:

Do not apply engine oil to the No. 1 crankshaft bearings or the contact surfaces.


HINT:

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the No. 1 crankshaft bearing. The amount visible on each side of the holes should be equal.



c.
A378025C02
0.573,2.844 0.719,2.625 false 0.635,2.073 0.792,2.271 0.156,0.198 10 false A 1.948,2.052 2.104,2.25 0.156,0.198 10 false B 0.448,2.885 0.698,3.094 0.25,0.208 10 true *a
*a Vernier Caliper


Using a vernier caliper, measure the distance between the cylinder block sub-assembly edge and the upper No. 1 crankshaft bearing edge.

Difference between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)



d.
A479896C01
2.219,3.333 2.573,3.125 false 2.604,2.938 2.917,3.135 0.313,0.198 10 false *a 0.594,3.844 0.906,4.042 0.313,0.198 10 false A 2.302,3.844 2.615,4.042 0.313,0.198 10 false B
*a Vernier Caliper


Install the 4 No. 2 crankshaft bearings to the 5 crankshaft bearing caps.


e.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and No. 2 crankshaft bearing edge.

Difference between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:

Do not apply engine oil to the No. 2 crankshaft bearings or the contact surfaces.



Hide 11791 7.INSTALL CRANKSHAFT THRUST WASHER

a.
A479875C01
1.365,1.125 1.24,0.406 1.24,0.406 1.958,1.385 true 1.625,1.292 1.26,0.448 true 1.094,0.177 1.333,0.375 0.24,0.198 10 true *a
*a Oil Groove


Install the 2 crankshaft thrust washers to the No. 3 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


b.

Apply engine oil to the crankshaft thrust washers.


Hide 13411 8.INSTALL CRANKSHAFT

a.

Apply engine oil to the No. 1 crankshaft bearings, and place the crankshaft on the cylinder block sub-assembly.


b.

Apply engine oil to the No. 2 crankshaft bearings.


c.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap set bolts.


d.
A479897C01
0.719,2.052 1.031,2.052 true 2.49,2.042 2.802,2.042 true 0.531,1.948 0.844,2.104 0.313,0.156 10 false *a 2.865,1.948 3.177,2.104 0.313,0.156 10 false *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Dimension:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the crankshaft bearing cap assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).




e.

Using a plastic hammer, lightly tap the crankshaft bearing cap assembly to ensure a proper fit.


f.

Install the crankshaft bearing cap set bolts.

NOTICE:

The crankshaft bearing cap set bolts are tightened in 2 progressive steps.



g.

Step 1:

i.
A479898N01
1.99,0.427 2.146,0.625 0.156,0.198 10 true 1 1.979,1.74 2.135,1.938 0.156,0.198 10 true 2 1.552,0.417 1.708,0.615 0.156,0.198 10 true 3 1.552,1.729 1.708,1.927 0.156,0.198 10 true 4 2.427,0.406 2.583,0.604 0.156,0.198 10 true 5 2.427,1.729 2.583,1.927 0.156,0.198 10 true 6 1.135,0.417 1.292,0.615 0.156,0.198 10 true 7 1.135,1.74 1.292,1.938 0.156,0.198 10 true 8

Uniformly install and tighten the 8 crankshaft bearing cap set bolts in the order shown in the illustration.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

HINT:

If a crankshaft bearing cap set bolt cannot be tightened to the specified torque, replace it.




h.

Step 2:

i.
A302206C04
2.26,0.729 2.635,0.406 true 2.667,0.281 2.979,0.438 0.313,0.156 10 false *a 1.552,0.385 1.865,0.542 0.313,0.156 10 false *b
*a Paint Mark
*b 90°
V100135

Front of Engine


Mark the front of the crankshaft bearing cap set bolts with paint.


ii.

Tighten the 8 crankshaft bearing cap set bolts 90° as shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



i.
A479899N01
1.323,0.146 1.479,0.344 0.156,0.198 10 false 1 0.635,0.229 0.792,0.427 0.156,0.198 10 false 2 0.74,1.927 0.896,2.125 0.156,0.198 10 false 3 1.719,0.125 1.875,0.323 0.156,0.198 10 false 4 1.698,1.979 1.854,2.177 0.156,0.198 10 false 5 2.021,0.104 2.177,0.302 0.156,0.198 10 false 6 2.021,1.927 2.177,2.125 0.156,0.198 10 false 7 1.385,1.979 1.542,2.177 0.156,0.198 10 false 8 2.708,0.333 2.865,0.531 0.156,0.198 10 false 9 2.667,1.823 2.823,2.021 0.156,0.198 10 false 10

Install and tighten the 10 bolts in the order shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


j.

Check that the crankshaft turns smoothly.


Hide 9.INSTALL CONNECTING ROD BEARING

a.
A479900C01
0.656,3.292 0.552,2.635 0.552,2.635 0.385,2.635 false 0.167,2.542 0.479,2.74 0.313,0.198 10 false *a 1.688,3.552 1.844,3.75 0.156,0.198 10 false A 2.865,3.521 3.021,3.719 0.156,0.198 10 false B
*a Vernier Caliper


Clean the connecting rod bearing contact surfaces of the connecting rod and connecting rod cap, and both surfaces of the 2 connecting rod bearings.


b.

Install the 6 connecting rod bearings to the 3 connecting rods and 3 connecting rod caps.


c.

Using a vernier caliper, measure the distance between the edges of the connecting rod and connecting rod bearing, and the edges of the connecting rod cap and connecting rod bearing.

Difference between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:

Do not apply engine oil to the connecting rod bearings or the contact surfaces.



Hide 10.INSTALL PISTON WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.


b.
A479894C01
1.76,1.813 1.281,1.969 1.281,1.969 1.896,1.823 true 2.052,0.01 2.542,0.198 0.49,0.188 10 false *1, *4 2.052,1.99 2.542,2.177 0.49,0.188 10 false *2, *5 0.813,1.01 1.125,1.208 0.313,0.198 10 false *3 1.052,1.896 1.365,2.094 0.313,0.198 10 false *a
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Upper Side Rail
*5 Lower Side Rail
*a Front Mark
V100136

Front of Engine


Position the piston rings so that the ring ends are as shown in the illustration.


c.

Confirm that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.

A479892C01
1.875,0.615 2.188,0.813 0.313,0.198 10 false *a 3.646,0.854 3.958,1.052 0.313,0.198 10 false *c 3.625,2.292 3.938,2.49 0.313,0.198 10 false *d 4.375,1.792 4.688,1.99 0.313,0.198 10 false *b
*a Press around the circumference *b Ring End
*c Correct *d Incorrect (Ends of the oil ring expander are overlapping)


NOTICE:
·

After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.

·

If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.

·

If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander.




d.
A479901C01
0.698,4.167 0.99,3.854 true 0.542,4.135 0.854,4.333 0.313,0.198 10 false *a
*a Front Mark


Using a piston ring compressor, push the correctly numbered piston with connecting rod into the cylinder with the front marks of each piston with connecting rod facing the front of the engine.

NOTICE:
·

When inserting the piston with connecting rod into the cylinder block sub-assembly, make sure the connecting rod does not contact the No. 1 oil nozzle sub-assembly.

·

Match each connecting rod cap to the correct connecting rod.




e.
A479902C01
1.031,0.698 1.677,0.792 true 0.854,0.583 1.167,0.781 0.313,0.198 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing the correct direction.


f.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


g.

Install the 6 connecting rod bolts.

NOTICE:

The connecting rod bolts are tightened in 2 progressive steps.



h.

Step 1:

i.
A479903

Using an E12 "TORX" socket wrench, alternately tighten the 2 connecting rod bolts in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



i.
A479907C01
2.125,0.573 2.396,0.156 2.396,0.156 2.542,0.156 false 1.146,1.563 1.563,1.146 false 1.365,0.406 1.823,0.604 0.458,0.198 10 false *b 2.615,0.073 2.927,0.271 0.313,0.198 10 false *a 1,1.531 1.313,1.729 0.313,0.198 10 false *a
*a Paint Mark
*b 90°
V100135

Front of Engine


Step 2:

i.

Mark the front of the connecting rod bolts with paint.


ii.

Tighten the connecting rod bolts 90° as shown in the illustration.


iii.

Check that the paint marks are now at a 90° angle to the front.



j.

Check that the crankshaft turns smoothly.


k.

Check the connecting rod thrust clearance.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE MECHANICAL)>CYLINDER BLOCK>DISASSEMBLY


Hide 12581A 11.INSTALL NO. 1 CYLINDER BLOCK INSULATOR

a.
A479870

Install the No. 1 cylinder block insulator to the cylinder block sub-aseembly.


Hide 12211 12.INSTALL NO. 1 VENTILATION CASE

NOTICE:

Perform this procedure only when replacement of the No. 1 ventilation case is necessary.


a.
A479869

Install 3 new oil separator gaskets to the No. 1 ventilation case.


b.
A479868

Install the No. 1 ventilation case to the cylinder block sub-assembly with the 3 bolts and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)