Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER (for G16E-GTS) › from 2020.09
RM36W0E _53 Suspension _087263 FRONT SUSPENSION _0447912 FRONT SUSPENSION MEMBER(for G16E-GTS) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(for G16E-GTS)  INSTALLATION  


PROCEDURE

Hide 48811 1.INSTALL FRONT STABILIZER BAR

Hide 2.INSTALL STEERING LINK ASSEMBLY

Hide 48069 3.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C445919

Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.


Hide 48068 4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 12363A 5.INSTALL ENGINE MOVING CONTROL ROD

a.

Install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.

Torque:
200 N*m (2039 kgf*cm, 148 ft.*lbf)


Hide 51201 6.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Slowly jack up the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

CAUTION:
C320210

·

The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:
·

Use attachments to keep the front suspension crossmember sub-assembly level.

·

Make sure that the front suspension crossmember sub-assembly not hit the protrusion of the reinforcement.

·
C430482C01
0.583,1.948 0.885,2.177 0.302,0.229 10 true *a 2.385,1.948 2.688,2.177 0.302,0.229 10 true *b
*a OK
*b NG


After installation, check that the claws of the steering column hole cover base are not disengaged.




b.
C449745

Install the front suspension crossmember sub-assembly to the vehicle body with the 4 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.
C445917

Install the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


d.

Lower the engine lifter.


e.

Install the engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


f.

Install the wiring harness clamp bracket to the front suspension crossmember sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 51218A 7.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.

Install the front suspension member reinforcement LH to the front suspension crossmember sub-assembly and vehicle body with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 51217A 8.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

HINT:

Perform the same procedure as for the LH side.


Hide 9.INSTALL EXHAUST SENSOR CLAMP BRACKET

a.

Install the exhaust sensor 2 clamps bracket to the front suspension crossmember sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 48069 10.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 11.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 12.CONNECT TIE ROD END SUB-ASSEMBLY LH

a.
C445920

Connect the tie rod end sub-assembly LH to the steering knuckle LH with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Do not damage the ball joint dust cover.

·

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.




b.

Install a new cotter pin.


c.
C447096C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the steering knuckle seal as shown in the illustration.

HINT:

Check that the steering knuckle seal is securely installed.



Hide 45046 13.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 14.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the front stabilizer link assembly LH to the front stabilizer bar with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 15.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53876A 16.INSTALL FRONT FENDER LINER LH

a.

Install the front fender liner LH to the vehicle body with the 3 screws.


Hide 53875A 17.INSTALL FRONT FENDER LINER RH

HINT:

Perform the same procedure as for the LH side.


Hide 18.INSTALL FRONT WHEELS

Hide 45260 19.CONNECT NO.2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 20.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 21.INSTALL COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 48069 23.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 24.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51447D 25.INSTALL CENTER NO. 4 ENGINE UNDER COVER

a.

Install the center No. 4 engine under cover to the vehicle with the 4 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51442C 26.INSTALL ENGINE UNDER COVER LH

a.

Install the engine under cover LH to the vehicle with the 2 clips.


Hide 51441C 27.INSTALL ENGINE UNDER COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 51410 28.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

a.

Install the No. 1 engine under cover assembly to the vehicle with the 4 bolts, 4 screws and 12 clips.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 29.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT