Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER (for G16E-GTS) › from 2020.09
RM36W0E _53 Suspension _087264 REAR SUSPENSION _0447922 REAR SHOCK ABSORBER(for G16E-GTS) A

REAR SUSPENSION  REAR SHOCK ABSORBER(for G16E-GTS)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48760B 1.INSTALL REAR SUSPENSION SUPPORT ASSEMBLY

a.

Secure the rear suspension support assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the rear suspension support assembly to the rear shock absorber assembly.


c.

Apply a few drops of adhesive to the threads of a new rear support to rear shock absorber nut.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
C450035C01
2.438,0.729 2.688,0.458 true 2.313,1.948 2.625,2.104 0.313,0.156 10 false *a 2.708,0.365 3.167,0.563 0.458,0.198 10 false SST 1.031,3.021 1.344,3.177 0.313,0.156 10 false *b 3.052,1.427 3.24,1.74 0.188,0.313 10 false *c
*a Torque Wrench Fulcrum Length
*b Turn
*c Hold


Using SST and a 6 mm hexagon socket wrench, hold the rear shock absorber rod and tighten a new rear support to rear shock absorber nut.

SST
09729-00170  

Torque:
Specified tightening torque : 25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Securely insert the 6 mm hexagon socket wrench into the rear shock absorber rod to prevent damage to the rear shock absorber assembly when tightening the rear support to rear shock absorber nut.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 200 mm (7.874 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

12 N*m (122 kgf*cm, 9 ft.*lbf)




Hide 48554A 2.INSTALL REAR SHOCK ABSORBER CAP

a.

Install the rear shock absorber cap to the rear shock absorber assembly.


Hide 48540 3.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY

a.
C445817C04
1,0.656 1.167,0.656 1.167,0.656 1.594,0.979 true 0.781,0.583 0.99,0.802 0.208,0.219 10 true *1
*1 Rear Axle Carrier Pin


Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut and plate washer.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



Hide 4.STABILIZE SUSPENSION

a.
C445824C01
0.448,2.073 0.781,2.073 false 1.469,1.656 1.99,1.76 false 0.125,1.26 0.281,1.458 0.156,0.198 10 true A 0.24,1.979 0.469,2.188 0.229,0.208 10 false *b 2.01,1.656 2.24,1.865 0.229,0.208 10 false *a
*a Wooden Block
*b Jack
V100155

Wooden Block Placement Location


Using a jack and a wooden block, apply load to the suspension so that the rear No. 2 suspension arm assembly is positioned as shown in the illustration.

Standard Length A:

8.6 mm (0.339 in.)


CAUTION:
C349515

·

Do not raise the jack up too high.

·

The vehicle could fall, resulting in a serious accident.



NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




Hide 48790 5.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY

a.

Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Tighten the bolt with the nut secured.




Hide 48540 6.CONNECT REAR SHOCK ABSORBER ASSEMBLY

a.
C445819N01
0.979,1.01 1.135,1.208 0.156,0.198 10 true A 2.375,0.885 2.531,1.083 0.156,0.198 10 true B

Connect the rear shock absorber assembly to the vehicle with the 2 bolts.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)

NOTICE:

Temporarily tighten bolt A and then fully tighten the 2 bolts in the order of B and A.



Hide 48540 7.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

a.
C450036C01
1.063,0.615 1.219,0.24 1.219,0.24 1.385,0.24 true 0.271,0.26 0.688,0.458 true 0.063,0.104 0.24,0.313 0.177,0.208 10 true *1 0.865,1.833 1.083,2.042 0.219,0.208 10 true *d 1.604,0.177 1.823,0.385 0.219,0.208 10 true *b 2.302,0.552 2.521,0.76 0.219,0.208 10 true *a 2.74,1.906 2.958,2.115 0.219,0.208 10 true *c
*1 Rear Axle Carrier Pin
*a Torque Wrench Fulcrum Length
*b Ball Joint Lock Nut Wrench
*c Turn
*d Hold


Using a ball joint lock nut wrench fully tighten the rear shock absorber assembly with the nut.

Torque:
Specified tightening torque : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

Hold the rear axle carrier pin while rotating the nut.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 149.75 mm (5.90 in.)) + torque wrench (fulcrum length of 400 mm (1.31 ft.)):

98.2 N*m (1001 kgf*cm, 72 ft.*lbf)




Hide 48840A 8.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 9.INSTALL REAR WHEEL