Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for G16E-GTS) › from 2020.09
RM36W0E _52 Drivetrain _087547 DRIVE SHAFT / PROPELLER SHAFT _0447996 FRONT DRIVE SHAFT ASSEMBLY(for G16E-GTS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for G16E-GTS)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43410C 1.INSTALL FRONT DRIVE SHAFT BEARING (for RH Side)

a.
C278916C02
0.344,0.583 0.604,0.583 false 0.49,1.656 1.031,1.656 true 0.198,1.573 0.656,1.771 0.458,0.198 10 false SST 0.177,0.49 0.49,0.646 0.313,0.156 10 false *a
*a Steel Plate


Using SST, a steel plate and a press, press in the front drive inboard joint assembly RH until a new front drive shaft bearing contacts the edge of the front drive inboard joint assembly RH.

SST
09710-30012  (09710-04061)

NOTICE:
·

Make sure the front drive shaft bearing contacts the edge of the front drive inboard joint assembly RH, but do not press it in more than necessary.

·

Do not apply weight to the dust cover and outer race of the front drive shaft bearing.




b.
C127665

Using a snap ring expander, install a new snap ring.

NOTICE:

The snap ring should be installed completely.



Hide 41336D 2.INSTALL FRONT DRIVE SHAFT DUST COVER RH (for RH Side)

a.
C445309C01
0.323,1.417 0.49,1.417 0.49,1.417 0.573,1.75 false 0.365,2.365 0.531,2.365 0.531,2.365 0.563,2.552 false 0.167,1.323 0.479,1.479 0.313,0.156 10 false *a 0.083,2.292 0.542,2.49 0.458,0.198 10 false SST 2.969,0.99 3.219,1.24 0.25,0.25 10 false (A)
*a Steel Plate


Using SST, a steel plate and a press, install a new front drive shaft dust cover RH to the front drive inboard joint assembly RH until the distance from the tip of the front drive inboard joint assembly RH to the front drive shaft dust cover RH reaches the specification as shown in the illustration.

SST
09527-10011  

Standard Distance (A):

58.8 to 59.4 mm (2.31 to 2.34 in.)


NOTICE:
·

Make sure to install the front drive shaft dust cover RH in the correct direction.

·

Do not damage the front drive shaft dust cover RH.




Hide 3.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C166359C04
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.177,0.49 0.354,0.208 10 *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:

105 to 115 g (3.70 to 4.06 oz)



d.

Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 4.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.

Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot.


b.
C112671N02
1.083,0.5 1.302,0.5 1.302,0.5 1.646,0.865 false 0.792,0.427 1.198,0.646 0.406,0.219 10 false SST

Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C112672N06
2.281,1.052 2.771,1.781 true 2.771,1.781 2.99,1.781 false 3.01,1.708 3.385,2.031 0.375,0.323 10 false SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00021  

Standard Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is not as specified, retighten SST.


Hide 43447E 5.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

a.

Install the front axle outboard joint boot clamp to the front axle outboard joint boot.


b.
C112669N05
0.667,0.531 0.896,0.531 0.896,0.531 1.542,1.021 true 0.375,0.448 0.75,0.677 0.375,0.229 10 false SST

Place SST onto the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C112670N06
1.729,1.208 2.24,1.479 2.24,1.479 2.469,1.479 true 2.521,1.396 2.958,1.583 0.438,0.188 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00021  

Standard Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is not as specified, retighten SST.


Hide 43040 6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C274277C02
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Remove the protective tape.


c.
C067417C08
1.281,1.719 2.01,1.677 2.01,1.677 1.771,1.438 true 2.063,1.625 2.229,1.771 0.167,0.146 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



d.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Be sure to install the tripod joint in the correct direction.




e.
F045046

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


f.

Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard Grease Capacity:

168 to 178 g (5.93 to 6.28 oz)



g.
C129505C01
1.76,1 1.333,0.25 1.333,0.25 2.083,0.594 true 1.125,0.125 1.844,0.271 0.719,0.146 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 7.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.

NOTICE:
·

Keep the grooves free of grease.

·

Keep the inside of the front axle inboard joint boot free of foreign matter.




b.
C445310C01
1.417,1.25 1.677,1.5 0.26,0.25 10 false (A) 1.417,2.958 1.667,3.208 0.25,0.25 10 false (A) 0.083,0.083 0.333,0.333 0.25,0.25 10 false *a 0.083,1.813 0.333,2.063 0.25,0.25 10 false *b
*a for LH Side
*b for RH Side


Check whether the dimension (A) of each drive shaft is within specification.

Dimension (A):
for LH Side 584.2 to 594.2 cm (1.92 to 1.95 ft.)
for RH Side 864.4 to 874.4 cm (2.84 to 2.87 ft.)



c.

While keeping dimension (A) within the specified length, equalize the pressure within the inboard joint with atmospheric pressure by slightly lifting the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 43448F 8.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Install the front axle inboard joint boot clamp to the front axle inboard joint boot.


b.
C241890N02
0.667,0.531 0.896,0.531 0.896,0.531 1.542,1.021 true 0.375,0.448 0.75,0.677 0.375,0.229 10 false SST

Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C241891N02
1.729,1.208 2.24,1.479 2.24,1.479 2.469,1.479 true 2.521,1.396 2.958,1.583 0.438,0.188 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00021  

Standard Clearance:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


If the clearance is not as specified, retighten SST.


Hide 43448G 9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.
C215097

Using needle-nose pliers, engage the claws and install the front No. 2 axle inboard joint boot clamp as shown in the illustration.

NOTICE:
·

Do not damage the front axle inboard joint boot.

·

Do not deform the claws.