Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY › from 2020.09
RM36W0E _52 Drivetrain _087547 DRIVE SHAFT / PROPELLER SHAFT _0448000 PROPELLER SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 37100 1.TEMPORARILY INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

a.

Completely remove any oil or the like and clean the contact surfaces of the transfer assembly and propeller shaft with center bearing assembly.


b.

Completely remove any oil or the like and clean the contact surfaces of the rear differential carrier assembly and propeller shaft with center bearing assembly.


c.
C451198C01
1.729,1.583 2.177,1.844 2.177,1.844 1.76,1.427 true 2.219,1.771 2.469,1.979 0.25,0.208 10 true *a
*a Matchmark


Align the matchmarks of the transfer assembly and propeller shaft with center bearing assembly.


d.

Temporarily install the propeller shaft with center bearing assembly to the transfer assembly with the 4 nuts and 4 washers.

NOTICE:

Make sure there is no oil on the nuts and washers. If oil is found on any nut and washer, clean it before installation.



e.

When reusing the propeller shaft with center bearing assembly:

i.
C451197C01
1.688,1.698 2.177,1.938 2.177,1.938 1.719,1.563 true 2.208,1.875 2.448,2.083 0.24,0.208 10 true *a
*a Matchmark


Align the matchmarks of the rear differential carrier assembly and propeller shaft with center bearing assembly.



f.

When replacing the propeller shaft with center bearing assembly:

i.
C451199C01
1.802,1.771 2.177,1.938 2.177,1.938 1.75,1.552 true 2.208,1.875 2.448,2.083 0.24,0.208 10 true *a
*a Alignment Mark


Align the alignment marks of the rear differential carrier assembly and propeller shaft with center bearing assembly.



g.

Temporarily install the propeller shaft with center bearing assembly to the rear differential carrier assembly with the 4 nuts and 4 washers.

NOTICE:

Make sure there is no oil on the nuts and washers. If oil is found on any nut and washer, clean it before installation.



h.

Temporarily install the center support bearing and 2 center No. 2 support bearing washers with the 2 bolts.

NOTICE:

Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.



Hide 37100 2.TIGHTEN PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

a.

Tighten the 4 nuts of the propeller shaft with center bearing assembly and transfer assembly to the torque specification.

Torque:
73.5 N*m (749 kgf*cm, 54 ft.*lbf)


b.

Tighten the 4 nuts of the propeller shaft with center bearing assembly and rear differential carrier assembly to the torque specification.

Torque:
73.5 N*m (749 kgf*cm, 54 ft.*lbf)


c.
C278925C01
2.208,0.313 2.667,0.51 0.458,0.198 10 false *a
*a 90°


Check that the center line of the center support bearing housing is perpendicular to the axis of the propeller shaft.


d.

Tighten the 2 bolts of the center support bearing to the torque specification.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 3.INSPECT AND ADJUST JOINT ANGLE

NOTICE:

Perform the measurement with a 4 post lift or pit so that the vehicle is supported by all 4 wheels as if it were on the ground.


a.

Before the angle measurement, stabilize each part by performing procedures like those described below.

i.

Rotate the propeller shaft several times by hand.


ii.

Set the jack to the rear differential, and raise and lower the rear differential.



b.

Using SST and a straightedge, measure the angle of the transfer flange (angle D) and the angle of the intermediate shaft (angle A).

C375302C04
1.271,0.854 1.427,0.854 1.427,0.854 1.625,1.281 true 4.51,1.5 5.021,1.5 false 5.594,1.531 6.104,1.531 false 4.5,0.823 4.823,0.219 4.823,0.219 5.01,0.219 false 3.74,0.177 4.052,0.375 0.313,0.198 10 false *a 4.031,0.281 4.344,0.479 0.313,0.198 10 false *b 4.656,1.104 4.969,1.302 0.313,0.198 10 false *c 4.031,1.104 4.344,1.302 0.313,0.198 10 false *c 5.594,2.302 5.906,2.5 0.313,0.198 10 false *d 4.896,2.063 5.208,2.26 0.313,0.198 10 false *e 1.125,0.75 1.438,0.948 0.313,0.198 10 false *f 4.208,1.396 4.521,1.594 0.313,0.198 10 false SST 6.156,1.438 6.469,1.635 0.313,0.198 10 false SST 5.063,0.115 5.375,0.313 0.313,0.198 10 false *1
*1 Straightedge - -
*a No. 1 Joint Angle *b D - A
*c 90° *d Angle A
*e Angle D *f Angle D Measurement Position


SST
09370-50010  

NOTICE:

Make sure the straightedge and SST are at a right angle.


i.

Subtract the measured angle of the intermediate shaft (angle A) from the measured angle of the transfer flange (angle D) to obtain the No. 1 joint angle.

Standard No. 1 Joint Angle:
Measurement Position Angle
D - A -1°56' +/- 1°




c.

Using SST, measure the angle of the intermediate shaft (angle A) and the angle of the propeller shaft (angle B).

C483372C02
4.427,1.615 4.823,1.615 false 2.208,1.615 2.604,1.615 false 3.198,0.323 3.51,0.521 0.313,0.198 10 false *a 3.5,0.448 3.813,0.646 0.313,0.198 10 false *b 2.458,2.198 2.771,2.396 0.313,0.198 10 false *c 4.458,2.198 4.771,2.396 0.313,0.198 10 false *d 4.854,1.542 5.167,1.74 0.313,0.198 10 false SST 1.917,1.542 2.229,1.74 0.313,0.198 10 false SST
*a No. 2 Joint Angle *b A - B
*c Angle A *d Angle B


SST
09370-50010  

i.

Subtract the measured angle of the propeller shaft (angle B) from the measured angle of the intermediate shaft (angle A) to obtain the No. 2 joint angle.

Standard No. 2 Joint Angle:
Measurement Position Angle
A - B 1°00' +/- 1°




d.

Using SST, measure the angle of the propeller shaft (angle B) and the angle of the rear differential (angle C).

C483373C02
3.469,1.677 3.698,1.677 false 2.24,1.677 2.635,1.677 false 4.938,1.792 5.156,1.438 5.156,1.438 5.302,1.438 true 3.135,0.198 3.448,0.396 0.313,0.198 10 false *a 3.448,0.333 3.76,0.531 0.313,0.198 10 false *b 2.479,2.042 2.792,2.24 0.313,0.198 10 false *c 3.5,1.823 3.813,2.021 0.313,0.198 10 false *d 3.729,1.615 4.042,1.813 0.313,0.198 10 false SST 1.948,1.594 2.26,1.792 0.313,0.198 10 false SST 5.354,1.365 5.667,1.563 0.313,0.198 10 false *e
*a No. 3 Joint Angle *b B - C
*c Angle B *d Angle C
*e Angle C Measurement Position - -


SST
09370-50010  

i.

Subtract the measured angle of the rear differential (angle C) from the measured angle of the propeller shaft (angle B) to obtain the No. 3 joint angle.

Standard No. 3 Joint Angle:
Measurement Position Angle
B - C 2°50' +/- 1°




e.

If the measured angle of the propeller shaft with center bearing assembly is not within the specified range, or there is vibration or noise, use the following procedure to adjust the propeller shaft with center bearing assembly.

i.

Support the propeller shaft with center bearing assembly with a jack.


ii.

Remove the 2 center support bearing mounting bolts.


iii.

Slowly lower the jack and separate the center support bearing.


iv.

Select an appropriate adjusting washer thickness from the table below, and obtain a washer set.

Adjusting Washer:
Part No. Thickness
90201-10123 2.0 mm (0.0787 in.)
90201-10081 4.5 mm (0.177 in.)
90201-10083 6.5 mm (0.256 in.)
90201-10084 9.0 mm (0.354 in.)
90201-10085 11.0 mm (0.433 in.)


NOTICE:
·

Use washers of the same thickness on the left and right sides.

·

Do not use 2 or more washers stacked together.





Hide 58041A 4.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR SUB-ASSEMBLY

a.

Install the front No. 1 floor heat insulator sub-assembly to the vehicle body with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 58166A 5.INSTALL FRONT FLOOR COVER LH

a.

Engage the 6 clamps to install the front floor cover LH to the vehicle body.


b.

Install the bolt and 3 clips.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58165C 6.INSTALL FRONT FLOOR COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 17410 7.INSTALL FRONT EXHAUST PIPE ASSEMBLY