Home › Engine / Hybrid System › G16E-GTS (INTAKE / EXHAUST) › EXHAUST PIPE › from 2020.09
RM36W0E _51 Engine / Hybrid System _095906 G16E-GTS INTAKE / EXHAUST _0449875 EXHAUST PIPE A

G16E-GTS INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Standard Length 43.0 mm (1.69 in.)
Minimum Free Length 41.5 mm (1.63 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new exhaust pipe gasket to the exhaust manifold converter sub-assembly.


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold Converter sub-Assembly
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the exhaust pipe gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Be careful with the installation direction of the exhaust pipe gasket.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly to the exhaust manifold converter sub-assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold Converter sub-Assembly
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly is consistent front-to-rear and left-to-right.



Hide 57543C 3.INSTALL CENTER NO. 1 FLOOR BRACE

a.

Install the center No. 1 floor brace to the body with the 2 nuts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 57533B 4.INSTALL FRONT FLOOR CENTER BRACE

a.

Install the front floor center brace to the body with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51447D 5.INSTALL CENTER NO. 4 ENGINE UNDER COVER

a.

Install the center No. 4 engine under cover to the body with the 4 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17430 6.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.


c.

Install the tail exhaust pipe assembly to the front exhaust pipe assembly with 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 7.INSPECT EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform "Inspection After Repair" after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION