Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0448030 MANUAL TRANSAXLE SYSTEM C

EA67F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  P050031  Vehicle Speed Sensor "A" No Signal  


DESCRIPTION

Vehicles which are equipped with ABS (Anti-lock Brake System) detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensors. Each speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU (brake actuator assembly). The skid control ECU (brake actuator assembly) converts the wheel speed signals into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to the speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



A115899E96
0.771,1.052 1.563,1.427 0.792,0.375 10 false from Speed Sensor 1.813,1.958 3.354,2.406 1.542,0.448 10 false Skid Control ECU (brake actuator assembly) 3.5,1.958 5.333,2.125 1.833,0.167 10 false Combination Meter Assembly 3.115,0.604 3.927,0.781 0.813,0.177 10 false 4-Pulse 5.042,0.604 5.854,0.781 0.813,0.177 10 false 4-Pulse 6.073,1.844 6.521,2.01 0.448,0.167 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P050031 Vehicle Speed Sensor "A" No Signal While vehicle being driven, no vehicle speed sensor signal transmitted to ECM for 5.25 seconds (2 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

ECM


Does not come on DTC stored SAE Code:
P0500

MONITOR DESCRIPTION

If there is no speed signal from the combination meter assembly even though the ECM determines that the vehicle is being driven, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then stores a DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

While driving the vehicle with any gear selected and the clutch engaged, allow the vehicle to decelerate so that fuel cut is performed for 6 seconds or more.

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

10.

Input the DTC: P050031.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

PROCEDURE

1.CHECK DTC OUTPUT (SFI SYSTEM)
a.

Check for SFI system DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B