Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2020.09–2021.11
RM36W0E _58 Vehicle Interior _087985 METER / GAUGE / DISPLAY _0420292 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication. In addition, for some systems, vehicle speed information may be received via CAN communication.


W/ ENTRY AND START SYSTEM


The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2 which uses this information to create the vehicle speed signal. The vehicle speed signal is output from the skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly) to the certification ECU (smart key ECU assembly) and then to the combination meter assembly. To create this signal, 12 V is output from terminal SI of the combination meter assembly to the certification ECU (smart key ECU assembly). The pulse signal is created by switching the transistor in the certification ECU (smart key ECU assembly) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the certification ECU (smart key ECU assembly). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*1: for TMC Made HV Model

*2: except TMC Made HV Model



W/O ENTRY AND START SYSTEM


The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2 which uses this information to create the vehicle speed signal. The vehicle speed signal consists of pulses sent to the combination meter assembly from the skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2. To create this signal, 12 V is output from terminal SI of the combination meter assembly. This voltage is sent to the skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2. The pulse signal is created by switching the transistor in the skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2 on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*1: for TMC Made HV Model

*2: except TMC Made HV Model



WIRING DIAGRAM

for TMC Made 5 Door:
E438524E01
0.125,1.656 2.24,2.365 2.115,0.708 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly)*1 0.125,2.344 1.729,3.021 1.604,0.677 10 false Skid Control ECU (Brake Actuator Assembly)*2 5.479,1.938 5.792,2.135 0.313,0.198 10 false 20 5.76,1.938 6.073,2.135 0.313,0.198 10 false SI 6.5,1.573 6.875,1.865 0.375,0.292 10 false 12 V 5.458,4.417 5.771,4.615 0.313,0.198 10 false 36 5.771,4.417 6.083,4.615 0.313,0.198 10 false +S 1.229,4.417 1.688,4.615 0.458,0.198 10 false SPD 1.24,6.854 1.698,7.052 0.458,0.198 10 false SPD 5.604,6.854 6.063,7.052 0.458,0.198 10 false SPD 2.094,1.24 2.406,1.438 0.313,0.198 10 false *1 1.688,1.24 2,1.438 0.313,0.198 10 false *2 2.052,1 2.51,1.198 0.458,0.198 10 false A38 1.646,1 2.104,1.198 0.458,0.198 10 false A36 1.698,0.792 2.01,0.99 0.313,0.198 10 false 14 2.094,0.792 2.406,0.99 0.313,0.198 10 false 11 3.708,0.885 4.021,1.083 0.313,0.198 10 false *3 2.708,1.938 3.021,2.135 0.313,0.198 10 false *4 4.844,1.938 5.156,2.135 0.313,0.198 10 false *4 4.375,2.052 4.833,2.25 0.458,0.198 10 false H46 3.052,2.052 3.51,2.25 0.458,0.198 10 false H45 3.083,1.844 3.396,2.042 0.313,0.198 10 false 13 4.417,1.844 4.729,2.042 0.313,0.198 10 false 28 1.625,4.417 1.938,4.615 0.313,0.198 10 false 27 1.625,6.865 1.938,7.063 0.313,0.198 10 false 42 5.417,6.854 5.729,7.052 0.313,0.198 10 false 9 3.073,2.573 4.667,3.115 1.594,0.542 10 false Certification ECU (Smart Key ECU Assembly)*4 5.74,5.594 6.948,5.979 1.208,0.385 10 false Combination Meter Assembly 0.479,5.01 1.719,5.458 1.24,0.448 10 false Radio and Display Receiver Assembly 0.823,7.469 1.417,7.719 0.594,0.25 10 false ECM*2 5.74,5.427 6.052,5.625 0.313,0.198 10 false H6 5.604,7.458 6.833,7.865 1.229,0.406 10 false Navigation ECU*5 5.604,7.292 6.063,7.49 0.458,0.198 10 false H82 0.833,7.292 1.292,7.49 0.458,0.198 10 false A54 0.479,4.844 0.938,5.042 0.458,0.198 10 false H79 2.458,6.854 2.771,7.052 0.313,0.198 10 false *2 4.49,6.854 4.802,7.052 0.313,0.198 10 false *5 0.083,8.167 1.333,8.5 1.25,0.333 10 false *1: for HV Model 0.083,8.5 1.833,8.833 1.75,0.333 10 false *2: for Gasoline Model 2.083,8.167 4.667,8.5 2.583,0.333 10 false *3: w/o Entry and Start System 2.094,8.51 4.677,8.844 2.583,0.333 10 false *4: w/ Entry and Start System 5.083,8.167 7,8.5 1.917,0.333 10 false *5: w/ Navigation System 1.24,0.896 1.698,1.094 0.458,0.198 10 false SP1 3.865,2.063 4.479,2.26 0.615,0.198 10 false SPDO 3.406,2.063 4.021,2.26 0.615,0.198 10 false SPD

for TMMF Made 5 Door:
E445255E01
0.115,1.042 1.719,1.719 1.604,0.677 10 false Skid Control ECU (Brake Actuator Assembly) 5.396,1.063 5.708,1.26 0.313,0.198 10 false 20 5.635,1.063 5.948,1.26 0.313,0.198 10 false SI 6.417,0.708 6.792,1 0.375,0.292 10 false 12 V 5.365,3.021 5.677,3.219 0.313,0.198 10 false 36 5.646,3.021 5.958,3.219 0.313,0.198 10 false +S 1.292,3.021 1.75,3.219 0.458,0.198 10 false SPD 1.292,5.26 1.75,5.458 0.458,0.198 10 false SPD 5.635,5.25 6.094,5.448 0.458,0.198 10 false SPD 1.906,0.615 2.219,0.813 0.313,0.198 10 false *1 1.5,0.615 1.813,0.813 0.313,0.198 10 false *2 1.854,0.396 2.313,0.594 0.458,0.198 10 false A39 1.438,0.396 1.896,0.594 0.458,0.198 10 false A37 1.896,0.188 2.208,0.385 0.313,0.198 10 false 34 1.521,0.188 1.833,0.385 0.313,0.198 10 false 4 3.646,0.271 3.958,0.469 0.313,0.198 10 false *3 2.604,1.052 2.917,1.25 0.313,0.198 10 false *4 4.729,1.063 5.042,1.26 0.313,0.198 10 false *4 4.26,1.167 4.719,1.365 0.458,0.198 10 false H46 2.927,1.167 3.385,1.365 0.458,0.198 10 false H45 2.969,0.948 3.281,1.146 0.313,0.198 10 false 13 4.313,0.958 4.625,1.156 0.313,0.198 10 false 28 1.688,3.021 2,3.219 0.313,0.198 10 false 27 1.75,5.167 2.063,5.365 0.313,0.198 10 false 42 5.438,5.25 5.75,5.448 0.313,0.198 10 false 9 2.979,1.688 4.573,2.229 1.594,0.542 10 false Certification ECU (Smart Key ECU Assembly)*4 5.26,4.167 7.104,4.583 1.844,0.417 10 false Combination Meter Assembly 0.417,3.615 2.188,4.104 1.771,0.49 10 false Radio and Display Receiver Assembly*6 0.865,5.698 1.458,5.948 0.594,0.25 10 false ECM*2 5.271,4 5.583,4.198 0.313,0.198 10 false H6 5.51,5.875 6.74,6.281 1.229,0.406 10 false Navigation ECU*5 5.51,5.688 5.969,5.885 0.458,0.198 10 false H82 1.719,5.354 2.177,5.552 0.458,0.198 10 false A54 0.417,3.448 0.875,3.646 0.458,0.198 10 false H79 3.021,5.25 3.333,5.448 0.313,0.198 10 false *2 4.104,5.25 4.417,5.448 0.313,0.198 10 false *5 0.167,6.75 1.417,7.083 1.25,0.333 10 false *1: for HV Model 0.167,7.083 1.917,7.417 1.75,0.333 10 false *2: for Gasoline Model 0.167,7.417 2.75,7.75 2.583,0.333 10 false *3: w/o Entry and Start System 0.167,7.75 2.75,8.083 2.583,0.333 10 false *4: w/ Entry and Start System 0.167,8.083 2.083,8.417 1.917,0.333 10 false *5: w/ Navigation System 1.042,0.292 1.5,0.49 0.458,0.198 10 false SP1 3.75,1.177 4.365,1.375 0.615,0.198 10 false SPDO 3.302,1.177 3.917,1.375 0.615,0.198 10 false SPD 2.125,5.365 2.583,5.563 0.458,0.198 10 false A55 2.177,5.156 2.49,5.354 0.313,0.198 10 false 41 0.167,8.417 2.667,8.75 2.5,0.333 10 false *6: w/ Audio and Visual System 3,3.01 3.313,3.208 0.313,0.198 10 false *6 2.188,5.583 2.5,5.781 0.313,0.198 10 false *7 1.781,5.583 2.094,5.781 0.313,0.198 10 false *8 2.5,7.75 5,8.083 2.5,0.333 10 false *7: for 1KR-FE 2.5,8.083 5,8.417 2.5,0.333 10 false *8: for M15A-FKS 4.104,6.802 4.417,7 0.313,0.198 10 false *9 2.5,8.417 5.75,8.75 3.25,0.333 10 false *9: w/ Stereo Component Amplifier Assembly 5.646,6.792 6.104,6.99 0.458,0.198 10 false SPD 5.396,6.802 5.708,7 0.313,0.198 10 false 11 5.302,7.208 5.917,7.406 0.615,0.198 10 false H137 5.292,7.375 7.073,7.792 1.781,0.417 10 false Stereo Component Amplifier Assembly*9

for 3 Door:
E455954E01
0.115,1.271 1.719,1.948 1.604,0.677 10 false Skid Control ECU (Brake Actuator Assembly) 5.396,1.063 5.708,1.26 0.313,0.198 10 false 20 5.635,1.063 5.948,1.26 0.313,0.198 10 false SI 6.417,0.708 6.792,1 0.375,0.292 10 false 12 V 5.365,3.021 5.677,3.219 0.313,0.198 10 false 36 5.646,3.021 5.958,3.219 0.313,0.198 10 false +S 1.292,3.021 1.75,3.219 0.458,0.198 10 false SPD 1.292,5.26 1.75,5.458 0.458,0.198 10 false SPD 5.635,5.25 6.094,5.448 0.458,0.198 10 false SPD 0.177,1.052 0.635,1.25 0.458,0.198 10 false A108 1.427,0.302 1.74,0.5 0.313,0.198 10 false 14 3.646,0.271 3.958,0.469 0.313,0.198 10 false *1 2.604,1.052 2.917,1.25 0.313,0.198 10 false *2 4.729,1.063 5.042,1.26 0.313,0.198 10 false *2 4.26,1.167 4.719,1.365 0.458,0.198 10 false H46 2.927,1.167 3.385,1.365 0.458,0.198 10 false H45 2.969,0.948 3.281,1.146 0.313,0.198 10 false 13 4.313,0.958 4.625,1.156 0.313,0.198 10 false 28 1.698,3.021 2.01,3.219 0.313,0.198 10 false 27 1.698,5.26 2.01,5.458 0.313,0.198 10 false 42 5.427,5.25 5.74,5.448 0.313,0.198 10 false 9 2.979,1.688 4.573,2.229 1.594,0.542 10 false Certification ECU (Smart Key ECU Assembly)*2 5.26,4.167 7.104,4.583 1.844,0.417 10 false Combination Meter Assembly 0.417,3.615 2.188,4.104 1.771,0.49 10 false Radio and Display Receiver Assembly*4 0.969,5.875 1.563,6.125 0.594,0.25 10 false ECM 5.271,4 5.583,4.198 0.313,0.198 10 false H6 5.51,5.875 6.74,6.281 1.229,0.406 10 false Navigation ECU*3 5.51,5.688 5.969,5.885 0.458,0.198 10 false H82 0.969,5.677 1.51,5.917 0.542,0.24 10 false A106 0.417,3.448 0.875,3.646 0.458,0.198 10 false H79 4.104,5.25 4.417,5.448 0.313,0.198 10 false *3 0.167,7.083 2.75,7.417 2.583,0.333 10 false *1: w/o Entry and Start System 0.167,7.417 2.75,7.75 2.583,0.333 10 false *2: w/ Entry and Start System 0.167,7.75 2.083,8.083 1.917,0.333 10 false *3: w/ Navigation System 1.042,0.292 1.5,0.49 0.458,0.198 10 false SP1 3.75,1.177 4.365,1.375 0.615,0.198 10 false SPDO 3.302,1.177 3.917,1.375 0.615,0.198 10 false SPD 0.167,8.083 2.667,8.417 2.5,0.333 10 false *4: w/ Audio and Visual System 3,3.01 3.313,3.208 0.313,0.198 10 false *4 4.115,6.802 4.427,7 0.313,0.198 10 false *5 0.167,8.417 3.417,8.75 3.25,0.333 10 false *5: w/ Stereo Component Amplifier Assembly 5.646,6.792 6.104,6.99 0.458,0.198 10 false SPD 5.385,6.802 5.698,7 0.313,0.198 10 false 11 5.302,7.208 5.917,7.406 0.615,0.198 10 false O122 5.292,7.375 7.073,7.792 1.781,0.417 10 false Stereo Component Amplifier Assembly*5

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.

Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B




A

2.CHECK FOR DTC (ENTRY AND START SYSTEM (FOR START FUNCTION))

B

7.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.CHECK FOR DTC (ENTRY AND START SYSTEM (FOR START FUNCTION))
a.

Check for entry and start system (for start function) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 454

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK COMBINATION METER ASSEMBLY (INPUT VOLTAGE)

B

3.CHECK COMBINATION METER ASSEMBLY (INPUT VOLTAGE)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-36 (+S) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

14.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)
4.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H46-28 (SPDO) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
5.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
E391284C21
1.448,0.438 1.865,0.667 0.417,0.229 0.917,2 1.042,1.354 true 1.573,0.469 1.885,0.667 0.313,0.198 10 false H6 0.854,2.031 1.167,2.229 0.313,0.198 10 false SI 2.948,3.698 3.406,3.896 0.458,0.198 10 false GND 1.281,3.979 1.438,4.177 0.156,0.198 10 false A 0.177,0.24 0.49,0.438 0.313,0.198 10 false *a 0.448,2.458 0.76,2.656 0.313,0.198 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


a.

Connect the H46 certification ECU (smart key ECU assembly) connector.


b.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


c.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester connection H6-20 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-28 (SPDO) - H6-20 (SI) Always Below 1 Ω
H46-28 (SPDO) or H6-20 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Result Proceed to
OK (for TMC Made HV Model) A
OK (except TMC Made HV Model) B
NG C



A

8.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

B

11.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

C

14.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)
8.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-11 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [SKID CONTROL ECU])
9.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
E391284C21
1.448,0.438 1.865,0.667 0.417,0.229 0.917,2 1.042,1.354 true 1.573,0.469 1.885,0.667 0.313,0.198 10 false H6 0.854,2.031 1.167,2.229 0.313,0.198 10 false SI 2.948,3.698 3.406,3.896 0.458,0.198 10 false GND 1.281,3.979 1.438,4.177 0.156,0.198 10 false A 0.177,0.24 0.49,0.438 0.313,0.198 10 false *a 0.448,2.458 0.76,2.656 0.313,0.198 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


a.

Connect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


c.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester connection H6-20 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the H6 combination meter assembly connector.


b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-20 (SI) - A38-11 (SP1) Always Below 1 Ω
H6-20 (SI) or A38-11 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

*1: for TMC Made 5 Door

*2: for TMMF Made 5 Door Gasoline Model

*3: for TMMF Made 5 Door HV Model

*4: for 3 Door


a.

Disconnect the A36*1, A37*2, A39*3 or A108*4 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-14 (SP1) - Body ground*1 Ignition switch ON 11 to 14 V
A37-29 (SP1) - Body ground*2 Ignition switch ON 11 to 14 V
A39-34 (SP1) - Body ground*3 Ignition switch ON 11 to 14 V
A108-14 (SP1) - Body ground*4 Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
12.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
E391284C21
1.448,0.438 1.865,0.667 0.417,0.229 0.917,2 1.042,1.354 true 1.573,0.469 1.885,0.667 0.313,0.198 10 false H6 0.854,2.031 1.167,2.229 0.313,0.198 10 false SI 2.948,3.698 3.406,3.896 0.458,0.198 10 false GND 1.281,3.979 1.438,4.177 0.156,0.198 10 false A 0.177,0.24 0.49,0.438 0.313,0.198 10 false *a 0.448,2.458 0.76,2.656 0.313,0.198 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


a.

Connect the A36*1, A37*2, A39*3 or A108*4 skid control ECU (brake actuator assembly) connector.

*1: for TMC Made 5 Door

*2: for TMMF Made 5 Door Gasoline Model

*3: for TMMF Made 5 Door HV Model

*4: for 3 Door



b.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


c.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester connection H6-20 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])

*1: for TMC Made 5 Door

*2: for TMMF Made 5 Door Gasoline Model

*3: for TMMF Made 5 Door HV Model

*4: for 3 Door


a.

Disconnect the H6 combination meter assembly connector.


b.

Disconnect the A36*1, A37*2, A39*3 or A108*4 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-20 (SI) - A36-14 (SP1)*1 Always Below 1 Ω
H6-20 (SI) or A36-14 (SP1) - Body ground*1 Always 10 kΩ or higher
H6-20 (SI) - A37-4 (SP1)*2 Always Below 1 Ω
H6-20 (SI) or A37-4 (SP1) - Body ground*2 Always 10 kΩ or higher
H6-20 (SI) - A39-34 (SP1)*3 Always Below 1 Ω
H6-20 (SI) or A39-34 (SP1) - Body ground*3 Always 10 kΩ or higher
H6-20 (SI) - A108-14 (SP1)*4 Always Below 1 Ω
H6-20 (SI) or A108-14 (SP1) - Body ground*4 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)

*1: for 1KR-FE

*2: for M15A-FKS

*3: for G16E-GTS

*4: w/ Navigation System

*5: w/ Audio and Visual System

*6: for TMMF Made 5 Door with Stereo Component Amplifier Assembly

*7: for 3 Door with Stereo Component Amplifier Assembly


a.

Disconnect the H6 combination meter assembly connector.


b.

Disconnect the A55*1, A54*2 or A106*3 ECM connector.


c.

Disconnect the H82 navigation ECU connector.*4


d.

Disconnect the H79 radio and display receiver assembly connector.*5


e.

Disconnect the H137*6 or O122*7 stereo component amplifier assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-36 (+S) - A55-41 (SPD)*1 Always Below 1 Ω
H6-36 (+S) - A54-42 (SPD)*2 Always Below 1 Ω
H6-36 (+S) - A106-42 (SPD)*3 Always Below 1 Ω
H6-36 (+S) - H82-9 (SPD)*4 Always Below 1 Ω
H6-36 (+S) - H79-27 (SPD)*5 Always Below 1 Ω
H6-36 (+S) - H137-11 (SPD)*6 Always Below 1 Ω
H6-36 (+S) - O122-11 (SPD)*7 Always Below 1 Ω
H6-36 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for HV Model A
for Gasoline Model B



A

17.CHECK VEHICLE TYPE

B

16.CHECK ECM
16.CHECK ECM

*1: for 1KR-FE

*2: for M15A-FKS

*3: for G16E-GTS

*4: w/ Navigation System

*5: w/ Audio and Visual System

*6: for TMMF Made 5 Door with Stereo Component Amplifier Assembly

*7: for 3 Door with Stereo Component Amplifier Assembly


a.

Disconnect the H6 combination meter assembly connector.


b.

Disconnect the A55*1, A54*2 or A106*3 ECM connector.


c.

Connect the H82 navigation ECU connector.*4


d.

Connect the H79 radio and display receiver assembly connector.*5


e.

Connect the H137*6 or O122*7 stereo component amplifier assembly connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the ECM.



Result:
Proceed to
OK
NG



OK

NG

17.CHECK VEHICLE TYPE
17.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Stereo Component Amplifier Assembly A
w/o Stereo Component Amplifier Assembly B



A

18.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

B

19.CHECK VEHICLE TYPE
18.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

*1: for TMMF Made 5 Door

*2: for 3 Door

*3: w/ Navigation System

*4: w/ Audio and Visual System


a.

Disconnect the H6 combination meter assembly connector.


b.

Disconnect the H137*1 or O122*2 stereo component amplifier assembly connector.


c.

Connect the H82 navigation ECU connector.*3


d.

Connect the H79 radio and display receiver assembly connector.*4


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the ECM.



Result:
Proceed to
OK
NG



OK

19.CHECK VEHICLE TYPE

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

19.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Navigation System A
w/ Audio and Visual System B
None of the above conditions are met C



A

20.CHECK NAVIGATION ECU

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

REPLACE COMBINATION METER ASSEMBLY

20.CHECK NAVIGATION ECU
a.

Disconnect the H6 combination meter assembly connector.


b.

Disconnect the H82 navigation ECU connector.


c.

Connect the H79 radio and display receiver assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-36 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the navigation ECU.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG